Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UNIPROT:A7KAX9 (grit)
 1,275 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

Four arch wire alloy products were evaluated against 400- or 600-grit finished stainless steel contact flats at 34 degrees C under prevailing atmospheric conditions. Six relative velocities (10, 1.0, 0.1, 5 x 10(-2), 5 x 10(-3), and 5 x 10(-4) mm/min) were evaluated as many as three times each in order to simulate a range of sliding motion which approaches the mean rate of tooth motion--that of 2.3 x 10(-5) mm/min. Measurements of the static and kinetic coefficients of friction were rather invariant for the stainless steel and nickel titanium arch wire products. In contrast, a slight increase and a definite decrease of both coefficients occurred for the cobalt-chromium and the beta-titanium arch wire products, respectively. On the presumption that tooth motion routinely occurs over a wide range of sliding rates, the stainless steel couple produced the lowest and the most consistent coefficients of friction, whereas the beta-titanium wire on stainless steel flats produced the highest and the most erratic coefficients of friction. These observations should prevail whenever the film layer of saliva breaks down at, for example, the contact points of arch wire and bracket wings.
 ...
PMID:Effects of sliding velocity on the coefficients of friction in a model orthodontic system. 263 66

The Ra's al-Hamra prehistoric fishermen lived in isolation on the Qurum rocky promontorium in Oman during the 5th-4th millennia BC. To date, they represent the most ancient and numerous human fossil group excavated from the Arabian peninsula. Like other contemporaneous archaeologically documented small communities along the desert Arabian coasts, they intensively exploited ocean resources and collected molluscs from nearby mangrove swamps. The present study analyzes aspects of dental anthropology (including crown variation, morphology, dental wear, and oral health), in 600 permanent teeth from 49 individuals of both sexes excavated at the Mesolithic RH5-site by the Italian Archaeological Mission in Oman from 1981 to 1985. In association with a general low degree of morphometric variation, the Ra's al-Hamra dental crowns show low sexual dimorphism and are consistently reduced in size. These features are unexpected in a preagricultural population, especially when these data are compared to other eastern African and near Middle Eastern prehistoric populations. These data are discussed within the general context of human dental structural reduction occurring during the post-Pleistocene and are interpreted according to the "increasing population density effect" model. There are other significant differences that characterize the Ra's al-Hamra dentitions with respect to both eastern and western prehistoric human groups. The frequency of numerous nonmetric crown traits supports the hypothesis that a microdifferentiation phenomenon occurred in this marginal area. The preliminary skeletal analysis and the palaeodemographic profile show that the Omani prehistoric fishermen were affected by genetic isolation and inbreeding as well as strong environmental stress. Because of the grit assimilated with dried fish and the high shellfish consumption, dental wear was extreme in all age groups at Ra's al-Hamra and occasionally was responsible for serious hematogenously spread infections. In spite of the great anthropological importance of ancient Arabian populations, very few studies on skeletal and dental samples have been completed. The present paper offers an odontological data set for future comparative research in the area.
 ...
PMID:Prehistoric "fish-eaters" along the eastern Arabian coasts: dental variation, morphology, and oral health in the Ra's al-Hamra community (Qurum, sultanate of Oman, 5th-4th millennia BC). 265 51

Accurate intracoronal castings can be produced using a castable ceramic--DICOR--for which there is a need to identify a suitable luting cement. The aim of this investigation was to evaluate the bond strength of three glass-ionomer luting cements and one resin cement to treated and untreated DICOR, enamel, and dentin surfaces. Forty "cerammed" DICOR specimens were assigned to four groups: (1-3) grit-blasting and bonding to each of the three glass-ionomer cements; and (4) acid-etching, silane coating, and bonding to the resin cement. Seventy enamel specimens were assigned to seven groups: (1-3) no etching and bonding to each of the glass-ionomer cements; (4-7) acid-etching and bonding to the glass-ionomer cements and the resin cement. Seventy dentin specimens were assigned to seven groups: (1-4) bonding to each of the three glass-ionomer cements and the resin cement; (5-7) polyacrylic acid preconditioning and bonding to each of the three glass-ionomer cements. The mean resin cement bond strengths (MN/m2) to DICOR (9.4) and to etched enamel (10.7) were significantly greater (p less than 0.01) than those of the glass-ionomer cements (DICOR, 0.8-1.2; enamel, 0.4-0.9). Preconditioning of enamel and dentin significantly increased (p less than 0.05) the bond strengths to the glass-ionomer cements. The mean bond strength of the resin cement to untreated dentin (4.3) was significantly higher (p less than 0.05) than the glass-ionomer bond strengths to untreated dentin (1.0-1.7) and to preconditioned dentin (2.1-3.3). The high bond strengths achieved with the resin cement are encouraging. Selected surface treatment of DICOR, enamel, and dentin prior to luting should be clinically useful.
 ...
PMID:A bond strength study of luted castable ceramic restorations. 265 32

Over the millennia various hominoids and hominids have subsisted on very different dietaries, depending on climate, hunting proficiency, food-processing technology, and available foods. The Australopithecines were not browsers and fruit-eaters with very high intakes of vitamin C; rather they were scavengers of kills made by other animals. The hominids who followed did include some cold-climate hunters of large game, but the amount of animal protein decreased with the advent of grain-gathering and decreased further with the introduction of cereal agriculture, with a concomitant decrease in body size. From what we know about food adequacy, preparation, and storage, the notion that the postulated "primitive" diet was generally adequate, safe, and prudent can be rejected. Over evolutionary time, many of our ancestors ate poorly, especially during climate extremes, and they were often at risk for vitamin deficiencies, food-borne diseases, and neurotoxins. Until the advent of modern processing technologies, dirt, grit, and fiber constituted a large part of most early diets.
 ...
PMID:What did our ancestors eat? 224 37

In order to examine the influence exerted by the differing design of individual water treatment plant units on the emission rate of micro-organisms and the associated degree of exposure to which plant personnel is subjected, measurements were taken at three different types of treatment plants. Measurements were made using "Biotest" RCS Air Samplers. The total count of colonies was determined by means of Agar Strips GK-A (tryptic soy agar). Enterobacteriaceae were quantitatively ascertained using Agar Strips C (MacConkey agar), particular attention being paid to the determination of the coliform bacteria as faeces indicators. Agar Strips S (mannitol salt agar) were used to measure the count of staphylococci using Agar Strips HS (rosa Bengal streptomycin agar). Before taking measurements, the prevailing climatic conditions were recorded. It could be ascertained that the enclosure of the inflow area (screw conveyor pump station and aerated grit removal tank) lead to a considerable increase in the concentration of microorganisms in the air within the housing. The values dropped however, when adequate ventilation was provided. Differing oxygen in the activated sludge tanks - finebubble aeration at the tank bottom or the blowing in of air via centrifugal blowers - lead to large variations in the emission rates. However, the less the waste water is agitated, the lower the emission rates. In the case of fine-bubble aeration, rates which are also normally to be found in the "non-burdened" outside air were even recorded close to the aeration tank. In cases of centrifugal blower, the aeration tank should be covered with a shield. With this type of aeration the waste water is emitted radially towards the walls of the tank. The use of a sprinkler unit on an aeration tank equipped with centrifugal blower - to avoid foam formation on the surface of the water - does not lead to an increase in the already high emission rate. An increase in air pollution through mould fungi from waste water treatment plants could not be found. In conclusion, it can be said that different individual plant unit designs have a large influence on the concentration of micro-organisms in the ambient air of places of work of waste water treatment plant personnel. Emission rates can be limited to such a degree that, even in the immediate vicinity of the plant units, a decrease of micro-organism concentrations can be attained as comparable to the area outside the treatment plant.
 ...
PMID:[Emission of microorganisms from sewage treatment plants depending upon construction differences of single structural parts]. 308 4

Enamel demineralization occurring adjacent to directly bonded orthodontic attachments is of great concern to orthodontists. The topical application of fluorides to enamel surfaces before acid etching and the bonding of the attachments is not recommended by many investigators. The objective of this study was to determine the enamel fluoride acquired from various topical fluoride agents and to determine the effect of the acquired fluoride on the tensile bond strength of an orthodontic bonding system. Fifty extracted maxillary central incisors were mounted in cups and the facial surfaces of the crowns were polished on 600-grit silicon carbide paper. Enamel microbiopsies were performed just off the midpoint of each tooth. Ten teeth served as controls and received no topical fluoride treatment, while a similar number were treated with either APF, SnF2, Duraphat, or Fluor Protector. The teeth were suspended in synthetic saliva 4 minutes after fluoride application. The topical fluoride agents were removed after 24 hours and the teeth were again suspended in synthetic saliva at 37 degrees C for 7 days. Enamel biopsies were again performed just off the midpoint of each tooth on the side not previously biopsied. The enamel surfaces were etched for 1 minute and the tensile bond strength of Concise orthodontic bonding system to the etched enamel surfaces was determined. The enamel surfaces acquired significantly different amounts of fluoride from the topical fluoride agents, but the bond strengths to these surfaces were not significantly different. The results of this in vitro study suggest that the application of topical fluoride agents to enamel surfaces 7 days before the bonding of orthodontic attachments will not have an adverse effect on bond strength.
 ...
PMID:The effect of topical fluoride treatment on enamel fluoride uptake and the tensile bond strength of an orthodontic bonding resin. 315 23

The purpose of this study was: to determine whether polishing standardized proximal root surfaces with dental floss, Superfloss, wood and plastic interdental cleaners, using a polishing paste, produces any significant change on root surface roughness; and to determine the effectiveness of different number of strokes in polishing. 80 tooth specimens were prepared, 10 in each of 8 sample groups. Each proximal root surface was standardized with 600A grit silicone carbide paper and polished with either waxed dental floss, Superfloss, wood or plastic interdental cleaners, using alkali aluminum silicate polishing paste. All specimens were mounted on a flossing machine and polished with 10 or 20 strokes. Before and after polishing, measurements were recorded with the Surfanalyzer 150 System to produce profile and average roughness tracings. Average maximum peak heights, mean number of peaks, and mean average roughness values were calculated from the tracings. The data were analyzed statistically by paired t-test and Student t-test. No significant mean differences were found between the number of strokes used. No significant differences were found for waxed dental floss in relation to the values analyzed. Significant differences were found for maximum peak heights for Superfloss following 20 strokes of polishing. However, no significant differences were found for Superfloss for mean number of peaks and average roughness. Significant differences were found for average roughness values, maximum peak heights, and mean number of peaks for the wood and plastic interdental cleaners. It was concluded that root surface roughness increased significantly with the use of wood and plastic interdental cleaners but not with waxed dental floss or Superfloss.
 ...
PMID:In vitro polishing effectiveness of interdental aids on root surfaces. 346 7

The surface characteristics of eight posterior and two anterior composite resins were studied by SEM and profilometric tracings. The materials included both chemically cured and light-cured resin systems. Two posterior materials were microfilled composites; the others were conventional or hybrid types. The anterior composites were of conventional and hybrid types. At various steps in the procedures the following polishing/brushing treatments were evaluated: 1) dry polishing with Sof-lex discs followed by brushing with toothpaste; and 2) wet polishing with diamond pastes of increasing fineness, followed by brushing with toothpaste. The base line before the polishing/brushing procedures was obtained by wet polishing on silicon-carbide paper (4000 grit). All materials could be polished to a comparable smoothness by the Sof-lex discs, but this polishing procedure was associated with the development of an amorphous surface layer. Polishing with diamond pastes gave various results, with a 20-fold difference in surface roughness values from the smoothest to the roughest material. Toothbrushing after polishing with the Sof-lex system increased the surface roughness for all materials, but to various degrees. The two microfilled and four of the conventional posterior composites showed comparable surface roughness values, whereas two remaining posterior and the two anterior materials showed two to three times higher surface roughness values after toothbrushing.
 ...
PMID:Surface characteristics of posterior composites after polishing and toothbrushing. 347 39

This study was designed to determine whether there was any measurable difference in the effectiveness of bacterial plaque removal between 4 commercially available dental flosses. By means of a highly standardized and controlled in vitro experimental model technique utilizing 50 freshly extracted third molars, the possibility of intra- and inter-individual variability was eliminated. Each tooth was individually mounted in a formatray block and the surface was finished to either a "planed" or "unplaned" surface configuration. The "planed" root surface (dentin) was achieved by using 600 grit wet-sandpaper for tooth surface reduction while the "unplaned" root surface was achieved by using 600 gift wet-sandpaper. The teeth were then individually processed to effect the growth of bacterial plaque (S. mutans) on the prepared surfaces. Each tooth was subsequently disclosed, flossed and photographed without interruption. The flossing was carried out on a flossing machine utilizing a controlled force of 50 g. A controlled direction of the stroke perpendicular to the long axis of the tooth, and a controlled frequency of flossing (2 strokes per trial) was used. The results of the clinical trials were evaluated utilizing Ektachrome slides of the previously flossed and disclosed tooth surfaces. The photographs were projected, measured, and statistically analyzed (Student t-test and paired t-test) for the effectiveness of plaque removal of the 4 dental flosses and the effect of root surface roughness on the ability of the flosses to remove bacterial plaque. It was found that on smooth, "planed" root surfaces, there were no measurable difference among the 4 flosses.(ABSTRACT TRUNCATED AT 250 WORDS)
 ...
PMID:In vitro effectiveness of dental floss in plaque removal. 351 74

The first effective method of performing facial dermabrasion employed the use of a wire brush. The introduction of diamond fraises has, in the author's opinion, provided greater safety and more versatility than the wire brush. The diamond fraise is a more exacting instrument and with the recent introduction of the extra-coarse grit diamond fraise, the instrument is as abrasive as the standard wire brush. The diamond fraise is more easily controlled by the less experienced surgeon and because of its availability in many different shapes, widths, and grits, it provides greater versatility to the surgeon than the wire brush.
 ...
PMID:Facial dermabrasion: advantages of the diamond fraise technique. 358 29


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>