Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UNIPROT:A7KAX9 (grit)
 1,275 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

Hydroxylapatite (HA)-coated and grit-blasted (non-HA-coated) titanium dental implants were inserted into healed extraction sites of canine mandibles. After six weeks, the animals were killed and the implants mechanically tested in torsion to failure. Interface attachment strength, implant/tissue compatibility, integrity of the HA coating, and the location of interface failure were evaluated. Mechanical testing demonstrated an interface torsional strength of 3.98 +/- 0.93 MPa for the HA-coated implants and 2.25 +/- 0.65 MPa for the grit-blasted implants. This represents a 76.9% improvement in the maximum torsional interface strength, and is statistically-significant (p = 0.0004). On qualitative histologic analysis, interface failure was seen to occur primarily at the HA/implant interface, although failure through the HA coating and regions of bone/HA interface failure were observed. The HA-coated implants had bone in direct apposition to their surface with no fibrous tissue interposition. The grit-blasted implants also had regions of direct bone-implant apposition, but these areas were limited to a smaller proportion of the total interface area. There was no evidence of breakdown or change in thickness of the HA coating.
 ...
PMID:Torsional stability of HA-coated and grit-blasted titanium dental implants. 129 18

Fifty-six endosseous cylindrical implants were placed in dog mandibles 12 weeks after the extraction of all mandibular premolars and first molars. Eight implants, four coated with 50 microns of hydroxylapatite (HA) and four grit-blasted and titanium-surfaced, were placed in each dog. Ideal implant placement sites were modified by creating standardized 3 x 5-mm facial dehiscence defects. Half the dehiscences were treated with a modified expanded polytetrafluoroethylene (PTFE) membrane; the remainder served as controls. After 8 weeks of healing, the animals were sacrificed and measurements made to determine the percentage of dehiscence repair. The HA-coated implants had a mean defect fill of 95.17% and the grit-blasted implants had a percent fill of 82.8% in the guided tissue regeneration (GTR) test group; the control implants demonstrated a mean fill of 55% and 39% in the HA-coated and grit-blasted implants, respectively. Significant differences (P less than .05) were noted between both test groups and the titanium control group, and between the HA test and HA control groups. Histologic evaluation showed significantly greater repair associated with HA-coated implants, as well as significant bone loss associated with clinically exposed membranes. It was concluded that within the limitations of this study, guided tissue regeneration is a viable option in treating defects associated with dental implants.
 ...
PMID:Histological and clinical comparisons of guided tissue regeneration on dehisced hydroxylapatite-coated and titanium endosseous implant surfaces: a pilot study. 166 24

The purpose of the present study was to evaluate the influence of different surface characteristics on bone integration of titanium implants. Hollow-cylinder implants with six different surfaces were placed in the metaphyses of the tibia and femur in six miniature pigs. After 3 and 6 weeks, the implants with surrounding bone were removed and analyzed in undecalcified transverse sections. The histologic examination revealed direct bone-implant contact for all implants. However, the morphometric analyses demonstrated significant differences in the percentage of bone-implant contact, when measured in cancellous bone. Electropolished as well as the sandblasted and acid pickled (medium grit; HF/HNO3) implant surfaces had the lowest percentage of bone contact with mean values ranging between 20 and 25%. Sandblasted implants with a large grit and titanium plasma-sprayed implants demonstrated 30-40% mean bone contact. The highest extent of bone-implant interface was observed in sandblasted and acid attacked surfaces (large grit; HCl/H2SO4) with mean values of 50-60%, and hydroxylapatite (HA)-coated implants with 60-70%. However, the HA coating consistently revealed signs of resorption. It can be concluded that the extent of bone-implant interface is positively correlated with an increasing roughness of the implant surface.
 ...
PMID:Influence of surface characteristics on bone integration of titanium implants. A histomorphometric study in miniature pigs. 132 61

This study evaluated the response of canine mandibular bone to loaded hydroxylapatite-coated (HAC) and grit-blasted titanium (GT) endosseous dental implants. Four dogs were partially edentulated in the maxilla and mandible. Two implants supporting freestanding prostheses were placed in each quadrant. Following 1 and 10 months of loading, the implants were evaluated. Soft-tissue pocket depths were not statistically different between the HAC and GT implants. Crestal bone loss was not significantly different between the two implants. However, the HAC implants had a statistically significant greater amount of bone apposed to their axial and apical surfaces compared to the GT implants.
 ...
PMID:Loaded hydroxylapatite-coated and grit-blasted titanium implants in dogs. 256 73

Four arch wire alloy products were evaluated against 400- or 600-grit finished stainless steel contact flats at 34 degrees C under prevailing atmospheric conditions. Six relative velocities (10, 1.0, 0.1, 5 x 10(-2), 5 x 10(-3), and 5 x 10(-4) mm/min) were evaluated as many as three times each in order to simulate a range of sliding motion which approaches the mean rate of tooth motion--that of 2.3 x 10(-5) mm/min. Measurements of the static and kinetic coefficients of friction were rather invariant for the stainless steel and nickel titanium arch wire products. In contrast, a slight increase and a definite decrease of both coefficients occurred for the cobalt-chromium and the beta-titanium arch wire products, respectively. On the presumption that tooth motion routinely occurs over a wide range of sliding rates, the stainless steel couple produced the lowest and the most consistent coefficients of friction, whereas the beta-titanium wire on stainless steel flats produced the highest and the most erratic coefficients of friction. These observations should prevail whenever the film layer of saliva breaks down at, for example, the contact points of arch wire and bracket wings.
 ...
PMID:Effects of sliding velocity on the coefficients of friction in a model orthodontic system. 263 66

A systematic mechanical and histologic evaluation of design variables affecting bone apposition to various biocompatible materials was undertaken. The variables investigated included material elastic modulus, material surface texture, as well as material surface composition. The implant materials included polymethylmethacrylate (PMMA), low-temperature isotropic (LTI) pyrolytic carbon, commercially pure (C.P.) titanium, and aluminum oxide (Al2O3). Implant surface texture was varied by either polishing or grit-blasting the various materials. Implant surface composition was varied by applying a coating of ultra-low temperature isotropic (ULTI) pyrolytic carbon to the various implants. A total of 12 types of implants were evaluated in vivo by placement transcortically in the femora of adult mongrel dogs for a period of 32 weeks. Following sacrifice, mechanical push-out testing was performed to determine interface shear strength and interface shear stiffness. The results obtained from mechanical testing indicate that for implants fixed by direct bone apposition, interface stiffness and interface shear strength are not significantly affected by either implant elastic modulus or implant surface composition. Varying surface texture, however, significantly affected the interface response to the implants. For each elastic modulus group the roughened surfaced implants exhibited greater strengths than the corresponding smooth surfaced implants. Undecalcified histologic evaluation of the implants demonstrated that the roughened implants exhibited direct bone apposition, whereas the smooth implants exhibited various degrees of fibrous tissue encasement. Thus, for implants utilizing direct bone apposition fixation, it appears that of the parameters investigated, implant surface texture is the most significant.
 ...
PMID:An evaluation of variables influencing implant fixation by direct bone apposition. 388 Mar 49

This study describes the biologic integration of grit-blasted titanium alloy (Ti-6A1-4V) implants that were press fit into the distal femoral canal of young adult rabbits and evaluated by histologic, histomorphometric, and biomechanical methods. Polished and aluminum oxide grit-blasted (4.2 +/- 0.7 microns surface roughness) solid implants were compared with titanium fibermetal implants. Nondecalcified cross sections were studied by histology, histomorphometry, and electron microscopy in the backscatter mode at 3, 6, and 12 weeks after implantation. Pullout strength was measured at 12 weeks. Data were analyzed by analysis of variance and post-hoc Student-Newman-Keuls and Scheffe's tests. The blasted implants had significantly more bone intimately in contact with the implant surface (31%) than the fibermetal (17%), or solid polished implants (15%). By 3 weeks, woven bone had formed directly on the surface of the blasted implants, whereas there was a discrete space between woven bone and the other implants. Active remodeling of bone was shown by fluorochrome uptake at the surface of the blasted implants at 12 weeks after implantation. The strength of fixation of blasted and fiber-metal implants was significantly greater than polished implants at 12 weeks after implantation. Direct attachment of newly formed bone onto the blasted implant surface was confirmed by backscatter electron microscopy. The results of this study indicate that grit-blasted titanium surfaces provide an excellent surface for bone implant integration.
 ...
PMID:Biology of grit-blasted titanium alloy implants. 755 21

The apposition of new bone to polished solid implants and to implants with surfaces that had been blasted with one of three methods of grit-blasting was studied in a rabbit intramedullary model to test the hypothesis that blasted implant surfaces support osseous integration. Intramedullary titanium-alloy (Ti-6Al-4V) plugs, press-fit into the distal aspect of the femoral canal, were implanted bilaterally in fifty-six rabbits. Four surface treatments were studied: polished (a surface roughness of 0.4 to 0.6 micrometer) and blasted with stainless-steel shot (a surface roughness of five to seven micrometers), with thirty-six-grit aluminum oxide (a surface roughness of five to seven micrometers), or with sixty-grit aluminum oxide (a surface roughness of three to five micrometers). Localized attachment of new bone to the surfaces of the blasted implants was present radiographically at twelve weeks. The total bone area was significantly affected by the level of the section (the diaphysis had a greater bone area than the proximal part of the metaphysis and the proximal part of the metaphysis had a greater bone area than the distal part of the metaphysis; p < 0.001) and the quadrant within each section (the posterior and anterior quadrants had greater bone area than the medial and lateral quadrants; p < 0.00001). The length of the bone-implant interface was significantly affected by the surface treatment (the length of the bone-implant interface for the implants that had been blasted with sixty-grit aluminum oxide was greater than the length for the polished implants; p = 0.02), the time after implantation (the interface was longer at six and twelve weeks than at three weeks; p < 0.00001), and the level of the section (the interface was longer at the diaphysis than at the proximal part of the metaphysis and longer at the proximal part of the metaphysis than at the distal part of the metaphysis; p = 0.004). Blasting of the surface of titanium-alloy implants did not have an effect on the area of bone formation around the implants, but it did significantly affect the area of bone formation on the implant and the shear strength at the bone-implant interface. The two effects were not necessarily parallel, as significantly less (p < 0.05) bone formed on implants that had been blasted with stainless-steel shot than on those blasted with aluminum grit, whereas their interface shear strengths were similar.
 ...
PMID:The influence of surface-blasting on the incorporation of titanium-alloy implants in a rabbit intramedullary model. 767 90

Cylindric titanium rods with different surfaces were axially implanted into the femora of sheep. The three surfaces were grit-blasted titanium, plasma-sprayed titanium and plasma-sprayed hydroxyapatite (HA). After 2 months, a 2-cm segment of the femoral shaft was completely resected to load the implant, and the animals were allowed full weight-bearing for 9 months. Biomechanical and histological evaluation of the implants was undertaken 2 months after implantation and 9 months after the segmental resection. The mechanical testings of well-fixed implants were performed 9 months after segmental resection. Loosening of 45% of the titanium-coated implants was observed in the first 3 weeks, but thereafter, no further loosening occurred. The HA-coated implants remained entirely fixed for 3 weeks, but thereafter, a progressively increasing incidence of loosening up to 55% after 9 months of loading was detected as subsidence on X-radiographs. The maximum push-out strength of the titanium-coated implants was 4.9 MPa compared with 2.3 MPa for HA-coated ones. No significant mechanical interlock between the grit-blasted surface and bone was observed. The HA coating was found to be delaminated in all unstable implants, whereas the titanium coating remained completely intact. Morphometric analyses of well-fixed rods showed complete bony ingrowth onto the HA surface, whereas the contact area between the bone and the two titanium surfaces was less than 40%. Concerning clinical significance bony ingrowth with long-term mechanical interlock between the implant surface and the bone cannot be achieved by grit-blasting or HA-coating.(ABSTRACT TRUNCATED AT 250 WORDS)
 ...
PMID:Mechanical and histological evaluation of hydroxyapatite-coated, titanium-coated and grit-blasted surfaces under weight-bearing conditions. 773 32

Excessive heat generation at the implant-bone interface may cause irreversible bone damage and loss of osseointegration. The effect of heat generation in vitro at the implant surface caused by abutment reduction with medium- and extra-fine-grain diamond and tungsten burs in a high-speed dental turbine was examined. Titanium-alloy abutments connected to a titanium-alloy cylindrical implant embedded in an acrylic-resin mandible in a 37 degrees C water bath were reduced horizontally and vertically. Temperature changes were recorded via embedded thermocouples at the cervix and apex of the implant surface. Analysis of variance for repeated measures was used to compare seven treatment groups. Thirty seconds of continuous cutting with standard turbine coolant caused a mean temperature increase of 1 degrees C with a maximum of 2 degrees C. Similar tungsten cutting caused a mean increase of 2 degrees C with a maximum of 4.7 degrees C, significantly higher than diamond reduction. Additional air-water spray for continuous tungsten cutting had no significant effect, while intermittent cutting for 15-second increments reduced the temperature increase by 75%. Thus, abutment reduction with medium-grit diamonds using intermittent pressure and normal turbine coolant is unlikely to cause an interface-temperature increase sufficient to cause irreversible bone damage and compromise osseointegration.
 ...
PMID:An investigation on heat transfer to the implant-bone interface due to abutment preparation with high-speed cutting instruments. 774 40


1 2 3 4 5 6 7 8 9 10 Next >>