Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UNIPROT:A7KAX9 (grit)
 1,275 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

Osteoblasts exhibit a more differentiated morphology on surfaces with rough microtopographies. Surface effects are often mediated through integrins that bind the RGD motif in cell attachment proteins. Here, we tested the hypothesis that modulating access to RGD binding sites can modify the response of osteoblasts to surface microtopography. MG63 immature osteoblast-like cells were cultured on smooth (Ti sputter-coated Si wafers) and rough (grit blasted/acid etched) Ti surfaces that were modified with adsorbed monomolecular layers of a comb-like graft copolymer, poly-(L-lysine)-g-poly(ethylene glycol) (PLL-g-PEG), to limit nonspecific protein adsorption. PLL-g-PEG coatings were functionalized with varying amounts of an integrin-receptor-binding RGD peptide GCRGYGRGDSPG (PLL-g-PEG/PEG-RGD) or a nonbinding RDG control sequence GCRGYGRDGSPG (PLL-g-PEG/PEG-RDG). Response to PLL-g-PEG alone was compared with response to surfaces on which 2-18% of the polymer sidechains were functionalized with the RGD peptide or the RDG peptide. To examine RGD dose-response, peptide surface concentration was varied between 0 and 6.4 pmol/cm(2). In addition, cells were cultured on uncoated Ti or Ti coated with PLL-g-PEG or PLL-g-PEG/PEG-RGD at an RGD surface concentration of 0.7 pmol/cm(2), and free RGDS was added to the media to block integrin binding. Analyses were performed 24 h after cultures had achieved confluence on the tissue culture plastic surface. Cell number was reduced on smooth Ti compared to plastic or glass and further decreased on surfaces coated with PLL-g-PEG or PLL-g-PEG/PEG-RDG, but was restored to control levels when PLL-g-PEG/PEG-RGD was present. Alkaline phosphatase specific activity and osteocalcin levels were increased on PLL-g-PEG alone or PLL-g-PEG/PEG-RDG, but PLL-g-PEG/PEG-RGD reduced the parameters to control levels. On rough Ti surfaces, cell number was reduced to a greater extent than on smooth Ti. PLL-g-PEG coatings reduced alkaline phosphatase and increased osteocalcin in a manner that was synergistic with surface roughness. The RDG peptide did not alter the PLL-g-PEG effect but the RGD peptide restored these markers to their control levels. PLL-g-PEG coatings also increased TGF-beta1 and PGE(2) in conditioned media of cells cultured on smooth or rough Ti; there was a 20x increase on rough Ti coated with PLL-g-PEG. PLL-g-PEG effects were inhibited dose dependently by addition of the RGD peptide to the surface. Free RGDS did not decrease the effect elicited by PLL-g-PEG surfaces. These unexpected results suggest that PLL-g-PEG may have osteogenic properties, perhaps correlated with effects that alter cell attachment and spreading, and promote a more differentiated morphology.
 ...
PMID:RGD-containing peptide GCRGYGRGDSPG reduces enhancement of osteoblast differentiation by poly(L-lysine)-graft-poly(ethylene glycol)-coated titanium surfaces. 1476 25

Immobilization of RGD peptides on titanium (Ti) surfaces enhances implant bone healing by promoting early osteoblastic cell attachment and subsequent differentiation by facilitating integrin binding. Our previous studies have demonstrated the efficacy of RGD peptide immobilization on Ti surfaces through the electrodeposition of poly(ethylene glycol) (PEG) (RGD/PEG/Ti), which exhibited good chemical stability and bonding. The RGD/PEG/Ti surface promoted differentiation and mineralization of pre-osteoblasts. This study investigated the in vivo bone healing capacity of the RGD/PEG/Ti surface for biomedical application as a more osteoconductive implant surface in dentistry. The RGD/PEG/Ti surface was produced on an osteoconductive implant surface, i.e. the grit blasted micro-rough surface of a commercial oral implant. The osteoconductivity of the RGD/PEG/Ti surface was compared by histomorphometric evaluation with an RGD peptide-coated surface obtained by simple adsorption in rabbit cancellous bone after 2 and 4 weeks healing. The RGD/PEG/Ti implants displayed a high degree of direct bone apposition in cancellous bone and achieved greater active bone apposition, even in areas of poor surrounding bone. Significant increases in the bone to implant contact percentage were observed for RGD/PEG/Ti implants compared with RGD-coated Ti implants obtained by simple adsorption both after 2 and 4 weeks healing (P<0.05). These results demonstrate that RGD peptide immobilization on a Ti surface through electrodeposited PEG may be an effective method for enhancing bone healing with commercial micro-rough surface oral implants in cancellous bone by achieving rapid bone apposition on the implant surface.
 ...
PMID:Bone healing of commercial oral implants with RGD immobilization through electrodeposited poly(ethylene glycol) in rabbit cancellous bone. 2154 63

The performance of medical implants and devices is dependent on the biocompatibility of the interfacial region between tissue and the implant material. Polymeric hydrogels are attractive materials for use as biocompatible surface coatings for metal implants. In such systems, a factor that is critically important for the longevity of an implant is the formation of a robust bond between the hydrogel layer and the implant metal surface and the ability for this assembly to withstand physiological conditions. Here, we describe the grafting of cross-linked hydrogel networks to titanium surfaces using grit-blasting and subsequent chemical functionalization using a silane-based adhesion promoter. Metal surface characterization was carried out using profilometry, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX) analysis. Hydrogel layers composed of poly(ethylene glycol)-dimethacrylate (PEG-DMA), poly(2-hydroxyethylmethacrylate) (PHEMA), or poly(ethylene glycol)/poly(acrylic acid) (PEG/PAA) semi-interpenetrating polymer networks (semi-IPNs) have been prepared. The mechanical properties of these hydrogel-metal assemblies have been characterized using lap-shear measurements, and the surface morphology was studied by SEM and EDX. We have shown that both high surface roughness and chemical functionalization are critical for adhesion of the hydrogel layer to the titanium substrate.
...
PMID:Grafting of cross-linked hydrogel networks to titanium surfaces. 2436 60