Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C1832588 (PSS)
 2,979 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

We report the preparation, characterization, and mechanical properties of polyelectrolyte/phosphorus dendrimer multilayer microcapsules. The shells of these microcapsules are composed either by alternating poly(styrenesulfonate) (PSS) and positively charged dendrimer G4(NH+Et2Cl-)96 or by alternating poly(allylamine hydrochloride) (PAH) and negatively charged dendrimer G4(CH-COO-Na+)96. The same multilayers were constructed on planar support to examine their layer-by-layer growth and to measure the multilayer thickness. Surface plasmon resonance spectroscopy (SPR) showed regular linear growth of the assembly upon each bilayer deposited. We probe the mechanical properties of these polyelectrolyte/dendrimer microcapsules by measuring force-deformation curves with the atomic force microscope (AFM). The experiment suggests that they are much softer than PSS/PAH microcapsules studied before. This softening is attributed to an enhanced permeability of the polyelectrolyte/dendrimer multilayer shells as compared with multilayers formed by linear polyelectrolytes. In contrast, Young's modulus of both dendrimer-based multilayers was found to be on the same order as that of PSS/PAH multilayers.
 ...
PMID:Assembly and mechanical properties of phosphorus dendrimer/polyelectrolyte multilayer microcapsules. 1604 42

The growth, morphology, and interaction/adhesion properties of supported poly(sodium 4-styrenesulfonate)/poly(allylamine hydrochloride) (PSS/PAH) and DNA/PAH multilayers were investigated by means of surface plasmon resonance spectroscopy, atomic force microscope (AFM) imaging, and AFM-related force measurements. Multilayers were assembled on a prelayer of poly(ethylenimine) (PEI) both with and without drying. SPR results showed a linear growth of the assembly in the case of PSS/PAH multilayers and nonlinear growth for DNA/PAH multilayers. Measurements of forces acting between a bare glass sphere and a multilayer-coated surface indicated repulsive or attractive forces, depending on surface charge, which suggests that, on approach, electrostatic forces dominate. On separation, we observed large pull-off forces in the case of positively charged multilayers and weak pull-off forces in the case negatively charged multilayers. Multiple adhesions and plateau regions observed on separation were interpreted in terms of a bridging of multiple polymer chains between the glass particle and the multilayer and a stretching of the polyelectrolyte loops. The dependence of the pull-off force on the number of deposited layers shows regular oscillations.
 ...
PMID:Interaction and adhesion properties of polyelectrolyte multilayers. 1604 93

A capillary wave technique was used to study the viscoelastic properties of floating polyelectrolyte multilayers of (PSS/PAH)(n) at the air-water interface. Oppositely charged polyelectrolyte layers were adsorbed onto two different Langmuir monolayers, either the lipid dimethyldioctadecylammonium bromide (DODAB) or the block copolymer poly(styrene-b-sodium acrylate) (PS-b-PAA). The results allow to propose a schematic representation of the multilayers in three zones: Zone I as a precursor, representing the adhesion between the Langmuir monolayer and the bulk polyelectrolyte multilayer. Zone II forms a bulk or core zone of the multilayer. Zone III as an outer zone in direct contact with the aqueous phase. The results show an increase of the elasticity after the formation of four polyelectrolyte layers accompanied by an apparent negative viscosity. This behaviour was interpreted as a translation of elasticity dominance from zone I to zone II. The Young modulus of seven layers was in the same order of magnitude as observed for planar polyelectrolyte multilayer films.
 ...
PMID:Surface viscoelastic properties of floating polyelectrolyte multilayers films: a capillary wave study. 1605 44

In an effort to improve the stability for long-term biosensor use, layer-by-layer self-assembly was explored as a potential technique to provide a diffusion barrier to encapsulated glucose oxidase inside alginate microspheres (<5 microm), fabricated using an emulsification technique. The total loss of encapsulated enzyme was reduced to less than 25 and 15% with the application of single PAH/PSS and crosslinked PAH/PAA coatings, respectively, in comparison to at least a 45% loss observed with uncoated and PDDA/PSS-coated microspheres. Furthermore, it was found that enzyme within PAH/PSS- and crosslinked PAH/PAA-coated spheres retained more than 84 and 60% of initial activity, respectively, after three months, whereas uncoated and PDDA/PSS-coated microspheres retained less than 20%.
 ...
PMID:Stable encapsulation of active enzyme by application of multilayer nanofilm coatings to alginate microspheres. 1609 91

The coupling of lipid molecules to polymer components in a planar biomimetic model membrane made of a lipid bilayer (dimyristoylphosphatidylcholine) supported by polyelectrolyte multilayers is studied. The polyelectrolyte support was prepared by layer-by-layer deposition of positively charged poly(allylamine hydrochloride) (PAH) and negatively charged poly(sodium 4-styrenesulfonate) (PSS). Two polymer sample terminations were considered: positively charged (PAH-terminated) and negatively charged (PSS-terminated). Neutron reflectometry studies showed that, whereas positively charged samples did not favor the deposition of lipid, negatively charged samples allowed the deposition of a lipid bilayer with a thickness of approximately 5 nm. In the latter case, formation of polyelectrolyte layers after the deposition of the lipid layer was also possible.
 ...
PMID:Formation of polyelectrolyte multilayer architectures with embedded DMPC studied in situ by neutron reflectometry. 1611 64

Layer-by-layer deposition of anionic and cationic polyelectrolytes readily converts polymeric ultrafiltration membranes into materials capable of nanofiltration. ATR-FTIR spectra confirm that layer-by-layer deposition occurs on the ultrafiltration substrates, and adsorption of as few as 2.5 bilayers of poly(styrenesulfonate) (PSS)/protonated poly(allylamine) (PAH) or 3.5 bilayers of PSS/poly(diallyldimethylammonium chloride) (PDADMAC) reduces the molecular weight cutoff of polyethersulfone ultrafiltration supports from 50 kDa to <500 Da. Deposition of multilayer polyelectrolyte films on 300 and 500 kDa membranes also decreases molecular weight cutoffs, but solute rejections are significantly lower when using these supports, suggesting that the polyelectrolyte films do not completely cover large (0.2-0.4 microm in diameter) pores. On the 50 kDa substrates, PSS/PDADMAC films containing 3.5 bilayers exhibit a 95% rejection of SO(4)(2-) and a chloride/sulfate selectivity of 27, whereas 4.5-bilayer PSS/PAH coatings show a glucose/raffinose selectivity of 100. Pure water flux for [PSS/PAH](3)PSS-coated membranes at 4.8 bar is 1.6 m(3)/(m(2)day), which is more than 2-fold higher than that through a commercial 500 Da membrane.
 ...
PMID:High-flux nanofiltration membranes prepared by adsorption of multilayer polyelectrolyte membranes on polymeric supports. 1626 24

The effect of temperature on the buildup of polyelectrolyte multilayers consisting of poly(styrenesulfonate) (PSS), poly(diallyldimethylammonium) (PDADMA), and poly(allylamine) (PAH) was studied by using a quartz crystal microbalance. The increase of temperature in the deposition process was shown to have a considerable effect on the rate of the layer-by-layer buildup. The effect of temperature on the PDADMA/PSS deposition was found to be stronger than on the PAH/PSS deposition. The increasing temperature was found to extend the exponential buildup regime in all of the studied systems. A buildup model was created to simulate the buildup and to explain the effect of temperature. The model is based on the assumption that each deposition step leads to a quasi-equilibrium between the concentration of the polymer repeating unit in solution and the composition of the layer. According to the model, the layer-by-layer buildup is inherently exponential, becoming linear whenever diffusion is not fast enough to carry the polymer within the entire thickness of the film. This buildup model is discussed jointly with the earlier published three-zone model of the polyelectrolyte multilayers. The rate of the buildup is characterized by growth exponent beta. The temperature dependence of the growth exponent is discussed in connection with the thermodynamic parameters of the deposition.
 ...
PMID:Effect of temperature on the buildup of polyelectrolyte multilayers. 1628 96

We have used anionic and cationic single-wall carbon nanotube polyelectrolytes (SWNT-PEs), prepared by the noncovalent adsorption of ionic naphthalene or pyrene derivatives on nanotube sidewalls, for the layer-by-layer self-assembly to prepare multilayers from carbon nanotubes with polycations, such as poly(diallyldimethylammonium) or poly(allylamine hydrochloride) (PDADMA or PAH, respectively), and polyanions (poly(styrenesulfonate), PSS). This is a general and powerful technique for the fabrication of thin carbon nanotube films of arbitrary composition and architecture and allows also an easy preparation of all-SWNT (SWNT/SWNT) multilayers. The multilayers were characterized with vis-near-IR spectroscopy, X-ray photoelectron spectroscopy (XPS), surface plasmon resonance (SPR) measurements, atomic force microscopy (AFM), and imaging ellipsometry. The charge compensation in multilayers is mainly intrinsic, which shows the electrostatic nature of the self-assembly process. The multilayer growth is linear after the initial layers, and in SWNT/polyelectrolyte films it can be greatly accelerated by increasing the ionic strength in the SWNT solution. However, SWNT/SWNT multilayers are much more inert to the effect of added electrolyte. In SWNT/SWNT multilayers, the adsorption results in the deposition of 1-3 theoretical nanotube monolayers per adsorbed layer, whereas the nominal SWNT layer thickness is 2-3 times higher in SWNT/polyelectrolyte films prepared with added electrolyte. AFM images show that the multilayers contain a random network of nanotube bundles lying on the surface. Flexible polyelectrolytes (e.g., PDADMA, PSS) probably surround the nanotubes and bind them together. On macroscopic scale, the surface roughness of the multilayers depends on the components and increases with the film thickness.
 ...
PMID:Layer-by-layer electrostatic self-assembly of single-wall carbon nanotube polyelectrolytes. 1637 3

Patterned multilayer films composed of poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrenesulfonate) (PSS) were prepared using dip and spin self-assembly (SA) methods. A silicon substrate was patterned with a photoresist thin film using conventional photolithography, and PAH/PSS multilayers were then deposited onto the substrate surface using dip or spin SA. For spin SA, the photoresist on the substrate was retained, despite the high centrifugal forces involved in depositing the polyelectrolytes (PEs). The patterned multilayer films were formed by immersing the PE-coated substrates in acetone for 10 min. The effect of ionic strength on the pattern quality in dip and spin multilayer patterns (line-edge definition and surface roughness of the patterned region) was investigated by increasing the salt concentration in the PE solution (range 0-1 M). In dip multilayer patterns, the presence of salt increased the film surface roughness and pattern thickness without any deformation of pattern shape. The spin multilayer patterns formed without salt induced a height profile of about 130 nm at the pattern edge, whereas the patterns formed with high salt content (1 M) were extensively washed off the substrates. Well-defined pattern shapes of spin SA multilayers were obtained at an ionic strength of 0.4 M NaCl. Multilayer patterns prepared using spin SA and lift-off methods at the same ionic strength had a surface roughness of about 2 nm, and those prepared using the dip SA and lift-off method had a surface roughness of about 5 nm. The same process was used to prepare well-defined patterns of organic/metallic multilayer films consisting of PE and gold nanoparticles. The spin SA process yielded patterned multilayer films with various lengths and shapes.
 ...
PMID:Modulating the pattern quality of micropatterned multilayer films prepared by layer-by-layer self-assembly. 1643 Mar 5

Tissue engineering research has been on going for many years, people are making all the effort to explore the cell functions in cellular level and even in molecular level. Making the cells functional in an in vitro environment is a preliminary goal for the implantation and repair of complicated tissues/organs. Fabricating artificial ECM to mimic the in vivo environment is an essential approach in tissue engineering. The work in this paper is to study how rat aorta smooth muscle cells (RASMCs) behave in two engineered cell culture scaffolds: gelatin- and fibronectin (FN)-coated micropatterns. The investigation on the initial attachment and further growth of SMCs cultured on gelatin- and FN-coated micropatterns was addressed. This study focused on both the characterization of gelatin and fibronectin assembly properties and cell responses to these two protein-coated micropatterns. Thin film patterns with gelatin and fibronectin coatings were fabricated on microscope glass slides using photolithography, electrostatic layer-by-layer self-assembly and lift-off (LbL-LO) technologies. In this work, the scaffolds were built up by commonly used polyelectrolyte materials and proteins through LbL process, containing cationic poly(diallyldimethylammonium chloride) (PDDA), poly(allylamine hydrochloride) (PAH), anionic poly(sodium 4-styrenesulfonate) (PSS), gelatin and fibronectin. The resulting polyelectrolyte thin films were characterized by contact angle (CA), quartz crystal microbalance (QCM), atomic force microscopy (AFM), and fluorescence microscopy. CA measurement shows the consistent hydrophylicity of gelatin surfaces in different number of layers with LbL deposition method. Different from our previous QCM measurement of gelatin, fibronectin does not show high electrostatic attraction to either positively or negatively charged polyelectrolytes, although it can be weakly assembled to both polyelectrolyte surfaces. AFM images show Gelatin- and FN-coated micropatterns are around 50-60 nm thick. RASMCs were cultured on these gelatin- and FN-coated micropatterns. It was observed that, for the cells cultured on gelatin-coated micropatterns, they initially landed on the gelatin-coated surface, not on the PDDA-coated surface in between. But further growth of the cells was affected by the shape of the patterns: strip pattern limited cell growth beyond the patterns, but square patterns could not. While, it was found interestingly, for the cells cultured on FN-coated micropatterns, SMCs initially landed on PDDA-coated surface, and then migrated to FN-coated both square and strip patterns. These findings indicate that both gelatin and fibronectin are adhesive proteins, but they have different effects on the initial attachment and later growth for SMCs.
 ...
PMID:Comparison of selective attachment and growth of smooth muscle cells on gelatin- and fibronectin-coated micropatterns. 1643 14


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>