Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C1832588 (PSS)
 2,979 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

Two combinations of sodium poly(4-styrene sulfonate) (PSS) and poly(allylamine hydrochloride) (PAH) of different chain length and charge density are employed to construct multilayer films. The polyelectrolytes are assembled layer-by-layer on colloidal particles in the absence of salt. We have investigated the formation and electrical characteristics of the films by using electric light scattering technique. The results show that the film thickness is independent of the chain length when fully charged PAH (at pH 4.6) is combined with fully charged PSS. When the films are prepared with less charged PAH (at pH 6.7) and fully charged PSS, lower thickness is found for the film with shorter polymer chains. In all cases, the thickness increment realized on addition of the polymer with lower molar concentration is partially lost on exposure to the solution with higher concentration of the oppositely charged partner. When the film growth is regular (at equal molar concentrations of the fully charged polyelectrolytes), the ratio of PSS to PAH charge, estimated from the electro-optical effect values, exceeds 1. The electro-optical effect is also higher for the films ending with PSS when fully charged PSS is combined with less charged PAH (at pH 6.7). This reveals the key role of the charge in the last-adsorbed layer for the electro-optical behavior of the whole film.
 ...
PMID:Effect of chain length and charge density on the construction of polyelectrolyte multilayers on colloidal particles. 1727 14

The formation of a complex between an anionic spherical polyelectrolyte brush (SPB) and the cationic surfactant cetyltrimethylammonium bromide (CTAB) is investigated. The SPB consists of long chains of the strong polyelectrolyte poly(styrene sulfonate) (PSS), which are bound chemically to a solid poly(styrene) core of 56 nm in radius. The SPB are dispersed in water, and the ionic strength is adjusted by addition of NaBr. The resulting complexes are investigated in dilute solution by dynamic light scattering, by electrophoretic light scattering, and by cryogenic transmission electron microscopy (cryo-TEM). The formation of the complex between the SPB and the surfactant can be monitored by a strong shrinking of the surface layer when adding CTAB to dilute suspensions (0.01 wt %) and by a decrease of the effective charge of the complexes. Complex formation starts at CTAB concentrations lower than the critical micelle concentration of this surfactant. If the ratio r of the charges on the SPB to the charge of the added surfactant is exceeding unity, the particles start to flocculate. Cryo-TEM images of the complexes at r = 0.6 measured in salt-free solution show that the surface layer composed of the PSS chains and the adsorbed CTAB molecules is partially collapsed: A part of the chains form a dense surface layer while another part of the chains or aggregates thereof are still sticking out. This can be deduced from the cryo-TEM micrographs as well as from the hydrodynamic radius, which is still of appreciable magnitude. The 1:1 complex (r = 1.0) exhibits a fully collapsed layer formed by the PSS chains and CTAB. If the complex is formed in the presence of 0.05 M NaBr, r = 0.6 leads to globular structures directly attached to the surface of the core particles. All structures seen in the cryo-TEM images can be explained by a collapse transition of the surface layer brought about by the hydrophobic attraction between the polyelectrolyte chains that became partially hydrophobic through adsorption of CTAB.
 ...
PMID:Binding of oppositely charged surfactants to spherical polyelectrolyte brushes: a study by cryogenic transmission electron microscopy. 1731 35

We report the influence of polyelectrolyte (PE) multilayer films prepared from poly(styrene sulfonate)-poly(acrylic acid) (PSS-PAA) blends, deposited in alternation with poly(allylamine hydrochloride) (PAH), on film wettability and the adsorption behavior of the protein immunoglobulin G (IgG). Variations in the chemical composition of the PAH/(PSS-PAA) multilayer films, controlled by the PSS/PAA blend ratio in the dipping solutions, were used to systematically control film thickness, surface morphology, surface wettability, and IgG adsorption. Spectroscopic ellipsometry measurements indicate that increasing the PSS content in the blend solutions results in a systematic decrease in film thickness. Increasing the PSS content in the blend solutions also leads to a reduction in film surface roughness (as measured by atomic force microscopy), with a corresponding increase in surface hydrophobicity. Advancing contact angles (theta) range from 7 degrees for PAH/PAA films through to 53 degrees for PAH/PSS films. X-ray photoelectron spectroscopy measurements indicate that the increase in film hydrophobicity is due to an increase in PSS concentration at the film surface. In addition, the influence of added electrolyte in the PE solutions was investigated. Adsorption from PE solutions containing added salt favors PSS adsorption and results in more hydrophobic films. The amount of IgG adsorbed on the multilayer films systematically increased on films assembled from blends with increasing PSS content, suggesting strong interactions between PSS in the multilayer films and IgG. Hence, multilayer films prepared from blended PE solutions can be used to tune film thickness and composition, as well as wetting and protein adsorption characteristics.
 ...
PMID:Polyelectrolyte blend multilayer films: surface morphology, wettability, and protein adsorption characteristics. 1739 99

With X-ray and neutron reflectivity, the structure and composition of polyelectrolyte multilayers from poly(allyl amine) (PAH) and poly(styrene sulfonate) (PSS) are studied as function of preparation conditions (salt concentration and solution temperature, T). The onset of a temperature effect occurs at 0.05 M NaCl (Debye length approximately 1 nm). At 1 M salt, the film thickness increases by a factor of 3 on heating the deposition solution from 5 to 60 degrees C. The PAH/PSS bilayer thickness is independent of the kind of salt (NaCl or KCl), yet its composition is different (more bound water for NaCl). At low T, the internal roughness is 33% of the bilayer thickness; it increases to 60% at high T. The roughening is accompanied by a total loss of bound water. At which temperature the roughening starts is a function of the kind of salt (50 degrees C for NaCl and 35 degrees C for KCl). The strong temperature dependence and the eventual loss of bound water molecules may be attributed to the hydrophobic force; however, there is an isotope effect, since the loss of bound water is less pronounced in the deuterated layers.
 ...
PMID:The influence of secondary interactions during the formation of polyelectrolyte multilayers: layer thickness, bound water and layer interpenetration. 1746 67

The amount of counterions, measured by means of X-ray photoelectron spectroscopy (XPS), in layer-by-layer (LbL) films of poly(allylamine hydrochloride) (PAH) and poly(styrene sulfonate) (PSS), prepared from solutions with various NaCl concentrations, is shown to be greatly influenced by the film drying process: a smaller amount of counterions is observed in films dried after adsorption of each layer, when compared with films that were never dried during the film preparation. This is attributed to the formation of NaCl nanocrystals during the drying process which dissolve when the film is again immersed in the next polyelectrolyte solution. The presence of bonded water molecules was confirmed in wet films indicating that the counterions near the ionic groups are immersed in a water network. The number of counterions is dependent on the amount of salt in polyelectrolyte solutions in such a way that for a concentration of 0.2 M the relative amount of counterions attains saturation for both dried and wet samples, indicating that the process which leads the aggregation of counterions near of the ionic groups is not influenced by the drying process. Moreover, it is proven for wet samples that the increase in salt concentration leads to a decrease in the number of PAH ionized groups as predicted by the Muthukumar theory [J. Chem. Phys. 120 (2004) 9343] accounting for the counterion condensation on flexible polyelectrolytes.
 ...
PMID:Counterions in layer-by-layer films--influence of the drying process. 1750 99

Adsorption on ZnO of sodium poly(acrylate) (PAA), sodium poly(styrene sulfonate) (PSS) and a monomer surfactant [hydroxyethylidene diphosphonate (HEDP)] was investigated in suspensions initially equilibrated at pH 7. Results demonstrate interplay in the adsorption mechanism between zinc complexation, salt precipitation, and ZnO dissolution. In the case of PAA, the adsorption isotherm exhibits a maximum attributed to the precipitation of zinc polyacrylate. PSS and HEDP formed high-affinity adsorption isotherms, but the plateau adsorption of HEDP was significantly lower than that of PSS. The adsorption isotherm of each additive is divided into two areas. At low additive concentration (high zinc/additive ratio), the total zinc concentration in the solution decreased and the pH increased upon addition. At a higher additive ratio, zinc concentration and pH increased with the organic concentration. The increase in pH is due to the displacement of hydroxyl ions from the surface and the increase in zinc concentration results from the dissolution of ZnO due to the complexation of zinc ions by the organics. The stability of the ZnO dispersions was investigated by measurement of the particle size distribution after addition of various amounts of polymers. The three additives stabilized the ZnO dispersions efficiently once full surface coverage was reached.
 ...
PMID:Adsorption mechanism and dispersion efficiency of three anionic additives [poly(acrylic acid), poly(styrene sulfonate) and HEDP] on zinc oxide. 1772 Jan 81

The aim of this study was to investigate the feasibility of negatively charged nano-carriers (nanoparticles), consisting of polymer blends of poly(lactide-co-glycolide) (PLGA) and poly(styrene-co-4-styrene-sulfonate) (PSS), to improve the loading capacity and release properties of a positively charged model protein, lysozyme, through an adsorption process. Nanoparticles were prepared by a solvent displacement method and characterized in terms of size, zeta-potential, morphology, as well as loading capacity of model protein lysozyme. Morphology of these particles was investigated using transmission electron microscopy (TEM), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The loading capacity of lysozyme was evaluated as a function of polymer blend ratio, protein concentration, pH, and ionic strength; in vitro release profiles were also studied. The results show that negatively charged nanoparticles were obtained using polymer blends of PLGA and PSS, characterized by increased net negative surface charge with increasing ratios of PSS. Moreover, protein loading capacity increased as function of PSS/PLGA ratio. Increased pH facilitated the adsorption process and improved the loading capacity. Maximum loading efficiency was achieved at salt concentrations of 50mM. In vitro release of lysozyme from the polymer blend nanoparticles was dependent on drug loading and full bioactivity of lysozyme was preserved throughout the process. These findings suggest that this is a feasible method to prepare nanoparticles with high surface charge density to efficiently adsorb oppositely charged protein through electrostatic interactions.
 ...
PMID:Charged nanoparticles as protein delivery systems: a feasibility study using lysozyme as model protein. 1802 60

The morphology of the sodium salt form of randomly copolymerized polystyrene sulfonate (Na-PSS) in water/THF(99/1 v/v) cast onto silicon wafers, was studied by using scanning electron microscope (SEM). The contents of the sulfonate repeat units in Na-PSS were 1.1, 2.4, 4.6, 10.8, and 15.6 mol%. Based on the observed SEM images, the morphology of the Na-PSS changed with increasing ionic group content. For 1.1 and 2.4 mol%, sphere-shaped aggregates were formed with average sizes of 90 nm and of 77 nm, respectively. For 4.6 mol% and 10.8 mol%, 20-30 nm-sized aggregates were close-packed and fused together, resulting a surface with large roughness and ca. 10 nm-sized pores were formed. As the mol% increased to 15.6, the surface became smoother and flat films were formed.
 ...
PMID:Effect of the charge on the morphology of sodium salt form of the randomly sulfonated polystyrene ionomer cast onto silicon wafers. 1804 10

Template directed Layer-by-layer (LbL) technology recently moved into the center of scientific attention, particularly as a versatile tool for bioencapsulation purposes. Its major advantages can be found in the striking simplicity of tuning wall properties and the complete control over layer thickness and permeability. Yet, for the most commonly applied pair of polyelectrolytes, poly(allylamine) hydrochloride (PAH) and poly(styrene sulfonate) sodium salt (PSS), the mandatory control of the successful deposition on plane and colloidal surfaces is currently only attainable by means of sophisticated and expensive equipment. Here we describe an alternative quantification method based on a simple colorimetric assay using the Bradford reagent, a cost-effective commercially available dye, and standard laboratory technical devices. The binding of the dye to PSS causes a distinct shift of the absorption maximum from 465 to 680 nm, providing a method for spectral quantification of submicrogram amounts of dissolved PSS during LbL coating with significant accuracy and excellent reproducibility. The method was successfully employed to quantify accurate polyelectrolyte loadings on several particles that have a general importance as LbL templates. Thus, this method can be recommended as standard laboratory technique for control of LbL encapsulation and will considerably broaden the applicability of this promising technology in biotechnology.
 ...
PMID:Colorimetric assay for sensitive poly(styrene sulfonate) quantification in a template directed polyelectrolyte-assembling process. 1821 61

The effects of temperature, pH, and salt concentration on the layer-by-layer (LBL) deposition of sodium poly(styrene sulfonate) (PSS)/poly[2-(dimethylamino)ethyl methacrylate] (PDEM) were investigated by use of a quartz crystal microbalance with dissipation (QCM-D). At pH 4, the frequency change (Deltaf) gradually decreased to a constant, indicating that the polyelectrolyte complexes of the layer were not dissolved. As the layer number increased, the -Deltaf oscillatedly increased, indicating that the thickness of the multilayer increased. At the same time, the dissipation change (DeltaD) oscillatedly increased with the layer number, indicating the chain interpenetration or complexation that led to the alternative swelling-and-shrinking of the outermost layer. For the same layer number, as the temperature increased, the amplitude of DeltaD increased, indicating that the chain interpenetration increased. The thickness also increased with temperature. Further increasing the pH to 7 led to a thicker layer, reflected in the larger amplitude of DeltaD. At pH 10, the polyelectrolytes no longer formed multilayers on the surface because of the lack of electrostatic interactions. On the other hand, the addition of NaCl also led to a thickness increase. The amplitude in DeltaD increased with NaCl concentration, indicating that the chain interpenetration increased. Our experiments indicated that the LBL deposition of polyelectrolytes was dominated by the chain interpenetration. Also, the polyelectrolyte complexes in the layer can redissolve into solution from the surface at a high temperature or a high salt concentration.
 ...
PMID:Role of chain interpenetration in layer-by-layer deposition of polyelectrolytes. 1829 Jun 42


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>