Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0432222 (SEM)
 47,337 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

The objective of the research is to investigate the elements of routine sandblast technique on the evolution of bending strength of dental infiltrated Al2O3 ceramics and the underlying erosion mechanism. The plane specimens of an infiltrated ceramic were manufactured, polished and then tested under the modified pen-like sandblasting apparatus (90 degrees erosive angle and 10 mm sandblasting distance), with different grit sizes, working pressure and disposing time. Half of samples were selected randomly and sintered subsequently with Vitadur alpha veneering porcelain. Before and after sintering, the three-point-bending strengths was measured, and the surfaces of dental porcelain were observed with SEM and LCSM. The bending strength of ceramics decreased significantly after sandblast as compared with that of empty control group. After the procedure of sintering the veneering porcelain, the descending evolution of bending strength slowed down. Under the present manufacturing conditions, grit size effect is prominent among those correlative elements of sand grit size, working pressure and disposing time. And fatigue cracking characterizes the mechanism of erosion of dental infiltrated Al2O3 ceramics.
 ...
PMID:[Effect of erosion on strength of dental infiltrated Al2O3 ceramics]. 1642 96

The aim of this study was to evaluate the osteogenic properties of magnetron sputtered dicalcium pyrophaosphate (DCPP) and hydroxylapatite (HA) coatings. Therefore, DCPP and HA coatings were deposited on grit-blasted titanium discs. The substrates were used as-prepared or received an additional heat treatment which changed the amorphous coating structure to a crystalline structure. Subsequently, rat bone marrow stromal cells were cultured for 1-24 days on the various substrates. DNA and alkaline phosphatase activity was determined after 1, 3, 5, 8, and 12 days of incubation. Osteocalcin expression was evaluated after 8, 12, 16, and 24 days of incubation. Scanning electron microscopical analysis of cell morphology and coating characteristics was done after 8 and 16 days of incubation. All assays were done in duplicate and in each assay all specimens were present in fourfold. Results demonstrated that the cells did not proliferate and differentiate on all amorphous coatings. SEM revealed that the amorphous coatings showed significant dissolution. On the crystalline DCPP and HA coatings an increase in DNA and alkaline phosphatase activity was seen starting at day 8 of incubation. Osteocalcin expression on the crystalline coatings started to increase at day 16 of incubation. SEM showed that the growth and differentiation of the cells was associated with extensive collagen fiber formation and surface mineralization in the form of globular accretions. Further, statistical testing revealed that proliferation and differentiation of the rat bone marrow stromal cells started significantly earlier on the crystalline HA coatings than that on the crystalline DCPP coatings. These results demonstrate that the rat bone marrow stromal cells proliferated and differentiated only on crystalline magnetron sputtered DCPP as well as HA coatings, which warrants the further in vivo analysis of the bone healing supporting properties of these coatings.
 ...
PMID:Growth behavior of rat bone marrow cells on RF magnetron sputtered hydroxyapatite and dicalcium pyrophosphate coatings. 1660 22

During the process of bone formation, titanium (Ti) surface is an important factor in the modulation of osteoblastic function. This study was conducted in order to determine the effects of different Ti surfaces on the biological responses of a human osteoblast-like cell line (MG63). MG63 cells were cultured on smooth (S), sandblasted large-grit and acid etching (SLA), hydroxyapatite (HA), hydroxyfluoride (HF), titanium nitrate (TIN), and diamond-like carbon (DLC) Ti. The morphology of these cells were assessed by SEM. The cDNAs prepared from the total RNAs of the MG63 were hybridized into a human cDNA microarray (1152 elements). The appearances of the surfaces observed by SEM were different on each of the six dental substrate types. The SLA and HA surfaces were determined to be rougher than the others. MG63 cells cultured on SLA and HA exhibited cell-matrix interactions. In the expression of genes involved in osseointegration, several genes, including bone morphogenetic protein, cadherin, integrin, and insulin-like growth factors, were upregulated on the different surfaces. Several genes, including fibroblast growth factor receptor 4, Bcl 2-related protein, and collagen, were downregulated on the different surfaces. The attachment and expression of key osteogenic regulatory genes were enhanced by the surface roughness of the dental materials used.
 ...
PMID:Effect of various implant coatings on biological responses in MG63 using cDNA microarray. 1662 96

This study compared the microtensile bond strength (MTBS) of three all-in-one adhesive systems and a two-step system using two types of burs to prepare the dentin surfaces. Flat coronal surfaces of 24 extracted human molars were produced using either regular-grit or superfine-grit diamond burs. Resin composite was then bonded to equal numbers of these surfaces using one of the four adhesives: Clearfil SE Bond (CSE), G-Bond (GB), SSB-200 (SSB) or Prompt L-Pop (PLP). After storage for 24 hours in 37 degrees C distilled water, the bonded teeth were sectioned into slices (0.7-mm thick) perpendicular to the bonded surface. The specimens were then subjected to microtensile testing and the bond strengths were calculated at failure. Bond strength data were analyzed by two-way ANOVA and the GamesHowell test for interaction between adhesive and type of cut dentin. The fractured surfaces were observed by SEM to determine the failure mode. In addition, to observe the effect of conditioning, equal numbers of the two bur-cut dentin surfaces of eight additional teeth were conditioned with the adhesives and observed by SEM. Based on the results, when CSE and SSB were bonded to dentin cut with a regular-grit diamond bur, the MTBS values were significantly lower than that of superfine bur-cut dentin; whereas, GB and PLP showed no significant differences in MTBS between the two differently cut surfaces. SEM observation of the fractured surfaces revealed a mixed mode (adhesive in some areas and cohesive in others in the same sample) of failure in all specimens except PLP, which showed cohesive failure within the adhesive for both types of bur preparation. Generally, SEMs of the conditioned surfaces using both types of burs showed partial removal of the smear layer for CSE, minimal for GB and SSB and complete removal for PLP. In conclusion, when cutting dentin, selecting the proper bur type is important for improving the bond strength of some self-etching adhesive systems.
 ...
PMID:Effect of different bur grinding on the bond strength of self-etching adhesives. 1680 39

This in vitro study evaluated the resin-dentin interface formed by two 2-step and two 1-step self-etching adhesive systems under SEM. Class V cavities (4 x 2.5 x 1.5 mm) were prepared on the buccal surfaces of 25 extracted intact human third molars using a carbide bur in a high-speed handpiece. Four self-etching systems with corresponding resins were used: two 2-step systems, AdheSE (Ivoclar Vivadent) and Contax (DMG Hamburg), one 1-step/2 components system Futurabond NR (Voco) and a 1-step/1 component adhesive G-Bond (GC Corp). An etch and rinse system, PQ Clear (Ultradent), was used as a control. The teeth were thermocycled (500 cycles, 5 degrees /55 degrees C, 30 seconds dwell time), and 2 sections were made longitudinally through the restorations with a low-speed diamond saw, producing approximately 1-mm wide samples. The samples were polished with silicon carbide paper of increasing grit (400-1000), demineralized (6N HCl, 30 seconds), deproteinized (2.5% NaOC1, 10 minutes), left to air dry for 24 hours in a desiccator under low vacuum pressure, gold sputtered and viewed under SEM (JEOL-JSM-6460LV). In the AdheSE, Contax and Futurabond NR specimens, resin tag penetration into the tubules and lateral tags could be seen. G-Bond showed different interface morphology, with a tight, thin continuous junction and almost no resin penetration into tubules. PQ Clear samples exhibited the highest number of resin tags with numerous lateral tags. A clearly defined hybrid layer was seen in the Contax and PQ Clear specimens. Investigated self-etching systems showed similar interfacial morphology with dentin, except for the 1 step/1 component adhesive G-Bond. The degree of demineralization and interaction with dentin correlated with the acidity of the self-etching primers/adhesives. Fewer resin tags were formed with self-etching primers/adhesives than with the etch and rinse system.
 ...
PMID:Morphological evaluation of 2- and 1-step self-etching system interfaces with dentin. 1715 82

The surface properties of three different resin composite materials which influence Streptococcus mutans biofilm formation were evaluated using an artificial mouth system (AMS). Specimens were prepared from Clearfil AP-X, Grandio, and Reactmer Paste, and each material was divided into two groups: (1) surface was ground with 800-grit silicon paper (SiC#800); or (2) surface was polished with up to 1- microm diamond paste (DP1 microm). Biofilms were grown on the surface of each specimen for 20 hours, and then subjected to vortex agitation followed by measurement of retained biofilms. Surfaces with retained biofilms were also inspected by SEM. Significant differences were detected in surface roughness (Ra) between the two polishing conditions for all materials. The quantity of retained biofilm was significantly less (p < 0.05) on Clearfil AP-X DP 1 microm than on Clearfil AP-X SiC#800. With Reactmer Paste, their surfaces registered the lowest amount of retained biofilm--but there were no significant differences between the two polishing conditions. In conclusion, polishing did not render all resin composites equally resistant to biofilm formation.
 ...
PMID:Surface properties of resin composite materials relative to biofilm formation. 1820 58

The current trend towards minimum-intervention dentistry has introduced laser technology as an alternative technique for cavity preparation. This study assessed the null hypothesis that enamel prepared either by Er,Cr:YSGG laser or conventional diamond bur is equally receptive to adhesive procedures. The buccal and lingual surfaces of 35 sound human molars were prepared with Er,Cr:YSGG laser or a medium-grit diamond bur. One etch&rinse (OptiBond FL) and three self-etch adhesives (Adper Prompt L-Pop, Clearfil SE Bond and Clearfil S3 Bond) were applied on laser-irradiated and bur-cut enamel, followed by the application of a 5-6 mm build-up of Z100. The micro-tensile bond strength (microTBS) was determined after 24 hours of storage in water at 37 degrees C. Prepared enamel surfaces and failure patterns were evaluated using a stereomicroscope and a field-emission-gun scanning electron microscope (Feg-SEM). The pTBS to laser-irradiated enamel was significantly lower than to bur-cut enamel (p<0.05), with the exception of Clearfil S3 Bond, which bonded equally effectively to both substrates. The latter presented the highest microTBS on laser-irradiated enamel, though it was not statistically different from the microTBS of OptiBond FL. SEM analysis revealed significant morphological alterations of the laser-irradiated enamel surface, such as areas of melted and recrystalized hydroxyapatite and deep extensive micro-cracks. In conclusion, the bonding effectiveness of adhesives to laser-irradiated enamel depends not only on the structural substrate alterations induced by the laser, but also on the characteristics of the adhesive employed.
 ...
PMID:Influence of Er,Cr:YSGG laser treatment on microtensile bond strength of adhesives to enamel. 1866 4

This study evaluated the influence of the method and period of storage on the adhesive bond strength of indirect composite resin to bovine dentin. Ninety bovine incisors were stored in three different solutions: 0.2% thymol, 10% formalin, and 0.2% sodium azide, during 3 periods of storage: 7 days, 30 days and 6 months, resulting in 9 groups (n = 10). The roots were cut off and the buccal surface was ground with #600-grit silicon carbide paper. The surface was conditioned with 37% phosphoric acid for 15 s and a composite resin restoration (TPH Spectrum) was fixed using a one-bottle adhesive system (Adper Single Bond) and a dual-cured resinous cement (Rely X ARC) under a load of 500 g for 5 minutes. The samples were serially cut perpendicular to the bonded interface to obtain slices of 1.2 mm in thickness. Each slab was trimmed with a cylindrical diamond bur resulting in an hourglass shape with a cross-sectional area of approximately 1 mm(2). The microtensile bond strength (microTBS) testing was performed in a testing machine (EMIC 2000 DL) at a 0.5 mm/minute crosshead-speed until failure. After fracture, the specimens were examined under SEM to analyze the mode of fracture. muTBS Means were expressed in MPa and the data were analyzed by two-way ANOVA (3X3) and the Tukey test (alpha = 0.05). The storage times of 7 and 30 days produced no significant difference irrespective of the solution type. The formalin and thymol solutions, however, did have a negative influence on bond strength when the teeth were stored for 6 months.
 ...
PMID:Influence of method and period of storage on the microtensile bond strength of indirect composite resin restorations to dentine. 1914 92

This study evaluated the effect of the C-factor and dentin preparation method (DPM) in the bond strength (BS) of a mild self-etch adhesive; the study also observed the SEM superficial aspects of the corresponding smear layer. For purposes of this study, 25 molars (n=5) were used in a bond strength test. The molars were divided into two parts (buccal and lingual): one part received a Class V cavity (C-factor=3) and the other received a flat surface (C-factor=0) with the same bur type (coarse diamond or carbide bur and fine diamond or carbide bur), both within the same dentin depth. Five teeth were prepared with wet 60-grit and 600-grit SiC papers. After restoration with Clearfil SE Bond, microtensile beans (0.8 mm2) were prepared and tested after 24 hours in a universal testing machine (0.5 mm/minute). An additional two teeth for each DPM were prepared for SEM evaluation of the smear layer superficial aspects. The BS values were submitted to one-way ANOVA, considering only the DPM (flat surfaces) and two-way ANOVA (C-Factor x DPM, considering only burs) with p=0.05. Although the DPM in the flat surfaces was not significant, the standard deviations of carbide bur-prepared specimens were markedly lower. The BS was significantly lower in cavities. The fine carbide bur presented the most favorable smear layer aspect. It was concluded that different dentin preparation methods could not prevent the adverse effect in bond strength of a high C-factor. A coarse cut carbide bur should be avoided prior to a mild self-etch adhesive, because it adversely affected bond strength. In contrast, a fine cut carbide bur provided the best combination: high bond strength with low variability, which suggests a more reliable bond strength performance.
 ...
PMID:Effect of the C-factor and dentin preparation method in the bond strength of a mild self-etch adhesive. 1967 51

The purpose of this study was to assess the relationship between quantitative light-induced fluorescence (QLF) values and demineralization depths in an enamel erosion model in vitro. Flat labial enamel surfaces of bovine incisors were ground with 800-grit SiC and coated with nail varnish, but also leaving rectangular windows of enamel uncoated. Subsequently, they were immersed in a lactic acid gel (pH 5.0) for 0 to 7 weeks to make an enamel erosion model. Carious lesions thus induced were analyzed by QLF and the demineralization depths measured using SEM/ EDS method at the end of each period. A wide range of erosive lesions were produced with a steady increase in both demineralizing depth and fluorescence loss (DeltaF) over time. With this model, a good correlation was exhibited between each DeltaF value and the demineralization depth. Results of this study indicated that QLF could detect and quantify mineral loss under the eroded surface of the enamel erosion model.
 ...
PMID:Relationship between fluorescence loss of QLF and depth of demineralization in an enamel erosion model. 1982 81


<< Previous 1 2 3 4 5 6 7 8 Next >>