Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0432222 (SEM)
 47,337 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

Sterilization by gamma radiation is a method often used for bone and extracted teeth banking. The bond strength of human dentin submitted to gamma rays has not been reported. Therefore, the aim of this study was to assess the effect of gamma radiation on dentin shear bond strength and morphology. The roots were removed from extracted human bicuspids and their crowns divided into two groups: an untreated control and crowns submitted to gamma radiation sterilization. The crowns were mounted in epoxy resin and the buccal enamel removed exposing the subjacent dentin. SBMPPlus adhesive system was applied to a 3-mm diameter area after 15 s of 35% phosphoric acid etching. The samples were mounted in composite resin cylinders and stored in distilled water at 37 degrees C for 24 h until the shear test. Dental fragments from both groups were prepared for SEM analysis. There was no statistically significant difference between the results of the shear test for the two groups according to the Tukey test (p > 0.05). Scanning electron micrographs also did not show alterations. These results indicate that gamma radiation neither affected the shear bond strength of SBMPPlus nor altered the dentin surface morphology.
 ...
PMID:Effect of gamma radiation on dentin bond strength and morphology. 1169 20

To evaluate the durability of dentin bonding over time, the nanoleakage of four dentin bonding systems (Single Bond, Stae, Clearfil SE Bond and PermaQuik) over 24 hours, three months, six months and 12 months, was investigated. Flat occlusal dentin surfaces from extracted human molars were finished with wet 600-grit silicon carbide paper and bonded with one of the dentin bonding systems following manufacturers' instructions. The bonded surface was covered with < 1 mm thick layer of Silux Plus resin composite and light cured for 40 seconds. The specimens in each dentin-bonding group were randomly assigned to four sub-groups and kept in phosphate buffered saline solution (pH 7.4) containing 0.01% sodium azide at 37 degrees C for 24 hours, three, six or 12 months. The margins of all specimens were finished and polished with Sof-Lex disks after initial 24-hour storage. At the end of each storage time, the surrounding tooth surfaces except for 1 mm adjacent to the restoration were coated with nail varnish. The samples were immersed in a 50% w/v solution of silver nitrate for 24 hours, placed in photodeveloping solution and exposed to fluorescent light for eight hours. The samples were cut longitudinally and buccoligually, polished, mounted on stubs, carbon coated and observed in a Field Emission-SEM using backscattered electron mode. The results showed that systems using phosphoric acid as the etchant had a line of silver deposition at the base of the hybrid layer. Silver deposition increased in all systems over 12-months storage, with PermaQuik changing the least. Nanoleakage of the dentin bonding systems increased slightly during the 12-month storage period, indicating that they may be subject to hydrolytic attack over time.
 ...
PMID:The effect of long-term storage on nanoleakage. 1169 86

Hydroxyapatite coatings are commonly applied to metallic biomedical implants to accelerate osseointegration. These coatings, usually produced by plasma spray techniques, can be obtained by alternative processes, like biomimetic process, electrolytic deposition, or electrophoretic process as well. Electrophoretic deposition of hydroxyapatite exhibits several advantages like simplicity and low cost. In this article, titanium sheets with three different surface finishing were coated with hydroxyapatite by using electrophoresis. Surface treatments include: (1) abrading with SiC paper; (2) abrading with SiC paper plus electrolytic etch with H3PO4 solution; and (3) blasting with alumina powder followed by etch with a solution containing H2O2 and HF. Stoichiometric hydroxyapatite was used to coat titanium sheets. Blasted samples were also coated using a calcium-deficient hydroxyapatite. SEM, XRD, and FTIR were employed to characterize titanium substrates and coatings produced. Results show that electrophoretic process can produce a uniform thin layer, satisfactorily adhered, of hydroxyapatite on treated titanium samples. Furthermore, sintering at 800 degrees C do not promote the decomposition of calcium-deficient hydroxyapatite.
 ...
PMID:Hydroxyapatite deposition by electrophoresis on titanium sheets with different surface finishing. 1183 53

Phosphate-dependent glutaminase (PDG) activity, a key enzyme of glutamine metabolism, was determined in neutrophils obtained from the intra-peritoneal cavity (PC) or bronchoalveolar space (BAS) after administration of 1 ml or 100 microl, respectively of saline, glycogen solution (1%) or lipopolysaccharide (LPS 0.1 mg (100 microl)(-1)). Neutrophils were obtained by lavage of both sites with 20 ml saline 24 h after the administration of the stimuli. Glycogen and LPS, depending on the site the cells were obtained from, differently modulated PDG activity. Cells from BAS stimulated by glycogen or LPS had raised PDG activity to 30.5 +/- 5.2 and 42.7 +/- 12.1 nmol min(-1) mg(-1) protein, respectively, when compared with saline (9.1 +/- 0.9 nmol min(-1) mg(-1) protein); mean +/- SEM. On the other hand, cells from PC showed different PDG activity: 52.0 +/- 12.6 nmol min(-1) mg(-1) for saline, 36.5 +/- 9.5 nmol min(-1) mg(-1) for glycogen, and 76.6 +/- 11.2 nmol min(-1) mg(-1) for LPS; mean +/- SEM. Therefore, PDG activity varies with the site from which neutrophils are obtained and the stimulus imposed. The effect of glutamine on nitric oxide (NO) and tumour necrosis factor (TNF) production by peritoneal neutrophils, obtained after glycogen administration, cultured in the presence of LPS (0.5 microg ml(-1)) was also examined. The addition of glutamine at concentrations varying from 2 to 20 mM did not markedly affect NO production. Glutamine alone at 2 mM did not modify the production of TNF but in the presence of LPS caused a significant decrease. So, glutamine may preserve the function of neutrophils during infections and injuries.
 ...
PMID:Evidence that glutamine is involved in neutrophil function. 1197 1

Dentin proteoglycans are fundamental constituents of the dentin matrix and are distributed ubiquitously both in dentin and cement. They have several important functional properties; in particular, they have a fundamental role in the maintenance and the correct stabilization of collagen fibers. The use of phosphoric acid on dentin, as proposed in most common dental adhesive systems to establish a reliable bond, may affect the molecular structure of proteoglycans. The aim of this study was to evaluate, after the application of EDTA or phosphoric acid on dentin, the dentin proteoglycans with an immunocytochemical approach with high resolution SEM. For this purpose, dentin disks obtained from recently extracted human molars were etched with a 35% water solution of phosphoric acid for 15 s, 30 s, and 60 s. Control specimens were conditioned with EDTA. Specimens were immunolabeled with a monoclonal antibody antichondroitin sulfate and visualized with a gold-conjugated secondary antibody. Conditioning dentin with EDTA resulted in a distinct labeling of the proteoglycans, as visualized on branching fibrillar structures in the order of 10-20 nm. The use of 35% phosphoric acid on dentin revealed a coagulation of proteoglycans after etching for 15 s while a very low labeling signal was detectable after 30 s. No labeling was obtained after etching dentin with phosphoric acid for 60 s. These results suggest that the use of 35% phosphoric acid on dentin is able to produce significant structural modifications of the dentin proteoglycans even after short application times. Additionally, when applied on the dentin surface for more than 30 s, phosphoric acid produces a dramatic decrease in proteoglycans' antigenicity, probably due to structural modifications of the three-dimensional conformation of these molecules.
 ...
PMID:Dentin proteoglycans: an immunocytochemical FEISEM study. 1200 Dec 44

In the present paper, the effects of polyacrylic acid (PAA) conditioning on the morphology and chemistry of bovine enamel surface and the resulting interfacial reactions are being investigated using photometric, microscopic (SEM, AFM), electron spectroscopic (XPS) and staining methods (neutral red dye). The results are compared to two reference surfaces obtained by simple grinding and by etching with a phosphoric acid solution. It is shown that PAA conditioning leads to the leaching of calcium and phosphorus ions, to the smoothening of the surface and probably to the formation of a polymeric film at the surface. A mechanism by which a preliminary PAA conditioning of the enamel leads to the reported higher bonding strength between enamel and glass ionomer cements is proposed.
 ...
PMID:On the interaction of polyacrylic acid as a conditioning agent with bovine enamel. 1206 27

The aim of this study was to investigate, in vitro, the morphological characteristics of demineralized primary enamel subjected to brushing with a dentifrice with or without fluoride. In order to do so, 32 enamel blocks were divided in 4 different groups containing 8 blocks each. They were separately immersed in artificial saliva for 15 days. The experimental groups were: C - control; E - submitted to etching with 37% phosphoric acid gel (30 s); EB - submitted to etching and brushing 3 times a day with a non-fluoridated dentifrice; EBF = submitted to etching and brushing 3 times a day with a fluoridated dentifrice. The toothbrushing force was standardized at 0.2 kgf and 15 double strokes were performed on each block. After the experimental period, the samples were prepared and examined under SEM. The control group (C) showed a smooth surface, presenting scratches caused by habitual toothbrushing. The etched samples (E) exhibited different degrees of surface disintegration, but the pattern of acid etching was predominantly the type II dissolution. The brushed surfaces were smooth, with elevations which corresponded to the exposure of Tomes' process pits and depressions which corresponded to interrod enamel. Particles resembling calcium carbonate were found in the most protected parts of the grooves. No morphological differences were observed between brushing with fluoridated (EBF) and non-fluoridated (EB) dentifrice. The results suggest that the mechanical abrasion caused by brushing demineralized enamel with dentifrice smoothes the rough etched surface, and the presence of fluoride does not cause morphological modifications in this pattern.
 ...
PMID:Microstructural analysis of demineralized primary enamel after in vitro toothbrushing. 1213 87

This study evaluated the effect of dentin conditioner on tensile bond strength to dentin prepared with different types of burs. A self-etching primer system, Mac-Bond II (MB, Tokuyama Dental) and a phosphoric acid etching system, Single Bond (SB, 3M) were used for conditioning. Twenty-four extracted intact human molars were ground flat to expose occlusal dentin. After the dentin surfaces were polished with #600 SiC paper, the teeth were randomly divided into a control group and three experimental groups according to the bur grits used: #600 SiC paper only as the control, fine cut steel bur (SB600), crosscut steel bur (SB703) and regular grit diamond bur (DB) mounted in a dental handpiece utilizing water cooling. The dentin surfaces were treated with one of two adhesive systems, then composite buildups were done with Clearfil AP-X (Kuraray Medical). After soaking the bond specimens for 24 hours in 37 degrees C water, multiple vertical serial sections (0.7 mm thick, 7-8 slices per one tooth) were made, trimmed to form an hour-glass shape with a 1.0 mm2 cross-section and tensile bond strengths were determined at a crosshead speed of 1 mm/minute. Statistical analysis was made using one and two-way ANOVA and Fisher's PLSD test (p<0.05). Six additional molars were used for SEM observations of the dentin surfaces of each group before and after treatment with the self-etching primer of MB, and another four teeth were used to observe the resin-dentin interface of each group of SB. Using MB, the DB group produced the lowest tensile bond strength (TBS) among the groups that received bur preparation, and there were no statistical differences among SB600, SB703 and the control. For SB, the TBS of SB703 was the highest, and there were no statistical differences among the other groups and the control. The influence of the method used to prepare dentin for micro-tensile bond strength testing was dependent on the adhesive system used.
 ...
PMID:Effect of self-etching primer vs phosphoric acid etchant on bonding to bur-prepared dentin. 1221 62

This study examined the interfaces between two dentin adhesives, namely, One Coat Bond, Clearfil SE Bond and a resin-modified glass ionomer cement (Fuji II LC) and the dentin of non-carious cervical lesions (NCCLs) with FE-SEM, and compared them with the interfaces produced with "normal" dentin. Fifteen human premolars each with a buccal NCCL were used. Cervical cavities were prepared on the lingual surface of the same teeth for the normal (control) dentin. All lesions and prepared cavities were cleaned with a slurry of pumice and water. The teeth were randomly divided among the three products that were applied according to the manufacturers' instructions. For the resin-bonded specimens, the cavities were restored with resin composite. All specimens were stored in 37 degrees C tap water. Resin-bonded specimens were observed using FE-SEM after treatment with 10% phosphoric acid, and 10% phosphoric acid and 5% sodium hypochlorite (NaOCl). The resin-modified glass ionomer cement (RM-GIC) specimens were observed after 10% phosphoric acid and 5% NaOCl treatment. The hybrid layer could be observed for the two adhesive systems in all specimens, but the thickness varied depending on the bonding system used and the dentin substrate. The results suggested that the hybrid layer produced in normal dentin was slightly thicker than that of NCCLs. Further, the hybrid layer thickness decreased in all specimens after NaOCl treatment.
 ...
PMID:Micromorphological study of resin-dentin interface of non-carious cervical lesions. 1221 69

The leachates generated at Hong Kong landfill sites contain high strength of ammonium-nitrogen (NH4+-N) over 3,000 mg l(-1) and are generally inhibitive to most biological treatment processes. To remove the NH4+-N from the landfill leachates and also recover the nitrogen as a struvite fertilizer, a lab-scale study was performed to investigate the feasibility of NH4+-N removal and struvite crystallization using different magnesium sources. Three combinations of chemicals, MgCl2 x 6H2O+Na2HPO4 x 12H2O, MgO+H3PO4 and MgSO4 x 7H2O+Ca(H2PO4) x H2O, were first used at different molar ratios to precipitate NH4+-N from the leachate. The experimental results indicated that NH4+-N was removed by 92%, 36% and 70% respectively at pH 9.0 and a molar ratio of Mg:N:P=1:1:1. Two synthetic seawater bitten wastes containing Mg2+ at 9,220 mg l(-1) and 24,900 mg l(-1) respectively were then used as a magnesium source, while 85% H3PO4 chemical was used as a phosphorus source. The results revealed that NH4+-N was removed by 80% and 72% respectively, while a molar ratio of Mg:N:P=1:1:1 was applied. In the final stage of experiments, the magnesium-ammonium-phosphate (MAP) precipitates were examined by SEM, EDS and XRD. The SEM micrographs of the MAP precipitates showed a typical morphology of elongated tubular and short prismatic crystals. The EDS and XRD results indicated that the chemical composition of the MAP precipitates depended on the chemicals used and experimental conditions. The study confirmed that the recovery of NH4+-N from landfill leachate and seawater bitten wastes could be effectively achieved by MAP precipitation to obtain struvite crystals with a composition of 5.1%N, 10.3%Mg and 16.5%P.
 ...
PMID:MAP precipitation from landfill leachate and seawater bittern waste. 1236 84


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>