Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0432222 (SEM)
 47,337 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

A stretchable e-textile was fabricated by simply soaking Spandex fabric in a conductive polymer aqueous dispersion, PEDOT-PSS. The resulting conductive fabric had an average conductivity of 0.1 S/cm. Subjecting the fabric to more than one soaking step increased the conductivity of the fabric up to ca. 2.0 S/cm resulting in a 33% faster switching speed. This simple methodology is not limited to Spandex (50% nylon/50% polyurethane). Several other fabric compositions were investigated for their conductivity via this process, including 100% cotton, 60% cotton/40% polyester, 95% cotton/5% Lycra, 60%polyester/40% rayon, 100% polyester, and 80% nylon/20% Spandex, listed in order of decreasing hydrophilicity. Those fabrics with higher water uptake resulted in higher conductivities upon soaking in PEDOT-PSS. Electrochromic polymers coated on the fabric could be switched between their different colored states, even upon stretching of the Spandex. SEM revealed that the electrochromic polymer coated on the substrate separated under stretching, uncovering the color of the base conducting fabric. It was found that the PEDOT-PSS was not a film on the Spandex but rather homogenously dispersed nanoparticles within the fabric matrix forming a percolated network.
ACS Appl Mater Interfaces 2010 Jun
PMID:Conductivity trends of PEDOT-PSS impregnated fabric and the effect of conductivity on electrochromic textile. 2048 42

Cotton fabric was treated with flame-retardant coatings composed of branched polyethylenimine (BPEI) and sodium montmorillonite (MMT) clay, prepared via layer-by-layer (LbL) assembly. Four coating recipes were created by exposing fabric to aqueous solutions of BPEI (pH 7 or 10) and MMT (0.2 or 1 wt %). BPEI pH 10 produces the thickest films, while 1 wt % MMT gives the highest clay loading. Each coating recipe was evaluated at 5 and 20 bilayers. Thermogravimetric analysis showed that coated fabrics left as much as 13% char after heating to 500 degrees C, nearly 2 orders of magnitude more than uncoated fabric, with less than 4 wt % coming from the coating itself. These coatings also reduced afterglow time in vertical flame tests. Postburn residues of coated fabrics were examined with SEM and revealed that the weave structure and fiber shape in all coated fabrics were preserved. The BPEI pH 7/1 wt % MMT recipe was most effective. Microcombustion calorimeter testing showed that all coated fabrics reduced the total heat release and heat release capacity of the fabric. Fiber count and strength of uncoated and coated fabric are similar. These results demonstrate that LbL assembly is a relatively simple method for imparting flame-retardant behavior to cotton fabric. This work lays the foundation for using these types of thin film assemblies to make a variety of complex substrates (foam, fabrics, etc.) flame resistant.
ACS Nano 2010 Jun 22
PMID:Flame retardant behavior of polyelectrolyte-clay thin film assemblies on cotton fabric. 2049 83

The potentials of low-pressure capacitively coupled RF oxygen and argon plasmas for the activation of polyester fibers surface that can enhance the deposition of colloidal TiO(2) nanoparticles were discussed. SEM and XPS analysis confirmed the plasma-induced morphological and chemical changes on the surface of polyester fibers. Oxygen and argon plasma pretreated polyester fabrics loaded with TiO(2) nanoparticles provided maximum reduction of Gram-negative bacteria E. coli and UV blocking. The self-cleaning effects tested on blueberry juice stains and photodegradation of methylene blue in aqueous solution proved excellent photocatalytic activity of TiO(2) nanoparticles deposited onto fiber surface. Although both plasmas significantly contributed to overall improvement of properties of such nanocomposite textile material, oxygen plasma treatment, in particular, enhanced the deposition of colloidal TiO(2) nanoparticles and thus ensured superior effects.
ACS Appl Mater Interfaces 2010 Jun
PMID:Improved properties of oxygen and argon RF plasma-activated polyester fabrics loaded with TiO2 nanoparticles. 2052 31

We have demonstrated the utility of hollow silica nanoparticles in fabricating conformal thin film nanoporous antireflection (AR) coatings on both poly(methyl methacrylate) (PMMA) and glass substrates. Layer-by-layer (LbL) assembly was successfully used to produce ultrathin AR coatings on planar and textured surfaces. Hollow silica nanoparticles were synthesized to extend the range of apparent refractive indices possible in an AR coating, enabling the design of both single index and graded index AR coatings on PMMA substrates. The diameter and shell thickness of the silica nanoparticles are the two independent, controllable parameters that we manipulated to tune the refractive index of the coating. The AR coatings reduced the minimum reflection of PMMA from 7% to 0.5%, while the maximum transmission increased from 92% to 98% at the optimized wavelength region that could be adjusted from the near UV into the visible. Cross sectional SEM showed that conformal coatings can be achieved on grooved PMMA Fresnel lenses. AFM was used to study surface topography on flat substrates.
ACS Nano 2010 Jul 27
PMID:Hollow silica nanoparticles in UV-visible antireflection coatings for poly(methyl methacrylate) substrates. 2053 11

Silica nanorods were successfully prepared through a sol-gel process in the presence of carboxylic-functionalized single-walled carbon nanotubes (C-SWCNTs). The effect of chemical functionalization of single-walled carbon nanotubes (SWCNTs) on the growth of the silica layer was investigated using pristine SWCNTs (P-SWCNTs) and C-SWCNTS. The C-SWCNTs served as a unique template to fabricate silica hybrid composite materials. The crystalline formation and growing mechanism of the silica layer on C-SWCNTs were explained by the hydrolysis and chemical bonding between silica precursors and carboxylated SWCNTs. The C-SWCNTs, as templates, were successfully encapsulated using silica, and used templates were removed by oxidation at high temperature. Finally, silica nanorods/nanowires were synthesized in forms of mold, and this silica fabrication mechanism could be applied for large-scale production of silica nanomaterials and highly flexible nanocomposites. The sequence of a silica encapsulation process of C-SWCNTs and removed C-SWCNTs was characterized using SEM, TEM, EDX, FT-IR and Raman spectroscopy, XRD, and electrical analysis.
ACS Nano 2010 Jul 27
PMID:Functionalization effects of single-walled carbon nanotubes as templates for the synthesis of silica nanorods and study of growing mechanism of silica. 2053 51

Multiwall carbon nanotube (MWNT)/manganese oxide (MnO2) nanocomposite ultrathin film electrodes have been created via redox deposition of MnO2 on layer-by-layer (LbL)-assembled MWNT films. We demonstrate that these LbL-assembled MWNT (LbL-MWNT)/MnO2 thin films consist of a uniform coating of nanosized MnO2 on the MWNT network structure using SEM and TEM, which is a promising structure for electrochemical capacitor applications. LbL-MWNT/MnO2 electrodes yield a significantly higher volumetric capacitance of 246 F/cm3 with good capacity retention up to 1000 mV/s due to rapid transport of electrons and ions within the electrodes. The electrodes are generated with two simple aqueous deposition processes: the layer-by-layer assembly of MWNTs followed by redox deposition of MnO2 at ambient conditions, thus providing a straightforward approach to the fabrication of high-power and -energy electrochemical capacitors with precise control of electrode thickness at nanometer scales.
ACS Nano 2010 Jul 27
PMID:Carbon nanotube/manganese oxide ultrathin film electrodes for electrochemical capacitors. 2055 96

Photocatalytic activity of Ag/TiO(2) composites obtained by photoreduction treatment (PRT) was investigated. The composite materials, containing various ratio of silver nanoparticles (0.6-3.7 wt %) were obtained by depositing silver on the Evonic-Degussa P25 titania surface. Selected samples whose color varied between light rose and purple brown were examined by SEM, TEM, XPS, DRS, and BET techniques. Flat band potential was determined using Roy method. TEM analysis showed spherically shaped silver nanoparticles of the diameter 4-12 nm. The XPS measurements revealed that silver particles were obtained mainly in metallic form. DRS spectra and photovoltage measurements showed that silver nanoparticles modified the P25 spectral properties but they changed neither the band gap nor the location of flat band potential. The photocatalytic activity of Ag/P25 composite was compared to the photocatalytic activity of pure P25 in the photooxidation reaction of an important potable water contaminant humic acid (HA) and two model compounds, oxalic acid (OxA) and formic acid (FA). The photodecomposition reaction was investigated in a batch reactor containing aqueous suspension of a photocatalyst illuminated by either UV or artificial sunlight (halogen lamp). The tests proved that a small amount of silver nanoparticles deposited on the titania surface triggers the increase in photocatalytic activity; this increase depends, however, on the decomposed substance.
ACS Appl Mater Interfaces 2010 Jul
PMID:Photocatalytic activity of titanium dioxide modified by silver nanoparticles. 2056 1

MnO2 nanoparticle enriched poly(3,4-ethylenedioxythiophene) (PEDOT) nanowires are fabricated by simply soaking the PEDOT nanowires in potassium permanganate (KMnO4) solution. The structures of these MnO2 nanoparticle enriched PEDOT nanowires are characterized by SEM and TEM, which show that the MnO2 nanoparticles have uniform sizes and are finely dispersed in the PEDOT matrix. The chemical constituents and bonding of these composite nanowires are characterized by energy-dispersive X-ray analysis, X-ray photoelectron spectroscopy, and infrared spectroscopy, which indicate that the formation and dispersion of these MnO2 nanoparticles into the nanoscale pores of the PEDOT nanowires are most likely triggered by the reduction of KMnO4 via the redox exchange of permanganate ions with the functional group on PEDOT. Varying the concentrations of KMnO4 and the reaction time controls the loading amount and size of the MnO2 nanoparticles. Cyclic voltammetry and galvanostatic charge-discharge are used to characterize the electrochemical properties of these MnO2 nanoparticle loaded PEDOT nanowires. Due to their extremely high exposed surface area with nanosizes, the pristine MnO2 nanoparticles in these MnO2 nanoparticle enriched PEDOT nanowires show very high specific capacitance (410 F/g) as the supercapacitor electrode materials as well as high Li+ storage capacity (300 mAh/g) as cathode materials of Li ion battery, which boost the energy storage capacity of PEDOT nanowires to 4 times without causing excessive volume expansion in the polymer. The highly conductive and porous PEDOT matrix facilitates fast charge/discharge of the MnO2 nanoparticles and prevents them from agglomerating. These synergic properties enable the MnO2 nanoparticle enriched PEDOT nanowires to be promising electrode materials for supercapacitors and lithium ion batteries.
ACS Nano 2010 Jul 27
PMID:Redox exchange induced MnO2 nanoparticle enrichment in poly(3,4-ethylenedioxythiophene) nanowires for electrochemical energy storage. 2059 Jan 28

The self-limiting reactions which distinguish atomic layer deposition (ALD) provide ultrathin film deposition with superb conformality over the most challenging topography. This work addresses how the shapes (i.e., surface profiles) of nanostructures are modified by the conformality of ALD. As a nanostructure template, we employ a highly scalloped surface formed during the first anodization of the porous anodic alumina (PAA) process, followed by removal of the alumina to expose a scalloped Al surface. SEM and AFM reveal evolution of surface profiles that change with ALD layer thickness, influenced by the way ALD conformality decorates the underlying topography. The evolution of surface profiles is modeled using a simple geometric 3D extrusion model, which replicates the measured complex surface topography. Excellent agreement is obtained between experimental data and the results from this model, suggesting that for this ALD system conformality is very high even on highly structured, sharp features of the initial template surface. Through modeling and experimentation, the benefits of ALD to manipulate complex surface topographies are recognized and will play an important role in the design and nanofabrication of next generation devices with increasingly high aspect ratios as well as nanoscale features.
ACS Nano 2010 Aug 24
PMID:Profile evolution for conformal atomic layer deposition over nanotopography. 2073 45

Ni-doped TiO2 film catalysts were prepared by a plasma electrolytic oxidation (PEO) method and were mainly characterized by means of SEM, EDS, XRD, XPS, and DRS, respectively. The effects of Ni doping on the structure, composition and optical absorption property of the film catalysts were investigated along with their inherent relationships. The results show that the film catalyst is composed of anatase and rutile TiO2 with microporous structure. Doping Ni changes the phase composition and the lattice parameters (interplanar crystal spacing and cell volume) of the films. The optical absorption range of TiO2 film gradually expands and shifts to the red with increasing dosages. Both direct and indirect transition band gaps of the TiO2 films are deduced consequently. Moreover, the photocatalytic activity of the film catalysts for splitting Na2S+Na2SO3 solution into H2 is enhanced by doping with an appropriate amount of Ni. The as-prepared TiO2 film catalyst doping with 10 g/L of Ni(Ac)2 presents the highest photocatalytic reducing activity.
ACS Appl Mater Interfaces 2010 Sep
PMID:Microporous Ni-doped TiO2 film photocatalyst by plasma electrolytic oxidation. 2079 10


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>