Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0432222 (SEM)
 47,337 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

A knee simulator was used to study the wear of carbon fiber reinforced UHMWPE (Poly Two) (Poly Two is a registered trademark of Zimmer, USA) tibial and patellar components against Ti-6A1-4V, titanium nitride (TiN)-coated Ti-6A1-4V, and cobalt-chromium-molybdenum femoral components. The prostheses tested were regular sized Miller-Galante total knees mounted on 316L stainless steel fixtures using bone cement. An environmental chamber surrounded the knee and maintained bovine serum lubricant at 37 degrees C. The specimens were tested using consecutive blocks of 464 level walking steps, 8 ascending stairs and 8 descending stairs for a total of 100,000 steps. The wear mechanisms found on the tibial components were scratching, carbon-fiber associated damage, surface deformation, pitting, minor abrasion, and delamination. Three forms of carbon fiber associated damage were identified; fibers pulled from the surface, broken fibers, and UHMWPE removed from the surface fibers. The SEM evaluation revealed a pit forming mechanism. No correlation was found between femoral component material and tibial surface damage. Visual examination of the femoral components revealed no signs of wear or scratching on the cobalt-chromium-molybdenum or TiN-coated Ti-6A1-4V components. There were, however, many light surface scratches on the uncoated Ti-6A1-4V components, which were also observed in a supplementary test of an uncoated Ti-6A1-4V component tested with a conventional polyethylene tibial component.
 ...
PMID:Component wear of total knee prostheses using Ti-6A1-4V, titanium nitride coated Ti-6A1-4V, and cobalt-chromium-molybdenum femoral components. 322 Aug 40

Grit blasting is a common procedure of roughening surfaces to promote physical attachment of porous coatings, but it has been shown to reduce fatigue strength. Shot peening is known to increase fatigue strength by inducing compressive surface stresses; however, it is not known how subsequent grit blasting affects these benefits. This study examines the endurance limits, Se, of ELI grade Ti-6A1-4V specimens under rotating cyclic bending, including polished (control); belted and beaded; belted, beaded, and grit blasted; and belted, beaded, shot peened, and grit blasted. Belting and beading resulted in a slight increase in Se, grit blasting caused a 15% reduction in Se from polished. Fifty percent of this reduction was recovered when shot peening preceded grit blasting, suggesting that residual compressive surface stresses, induced by peening, were not eliminated by the blast process. Roughness averages and RMS values did not correlate with Se trends. SEM results showed classical fatigue fractures, consistent with surface crack initiation.
 ...
PMID:Effects of precoating surface treatments on fatigue of Ti-6A1-4V. 749 7

The bone-bonding behavior of three kinds of bioactive ceramics coated on titanium alloy by the plasma-spray technique was investigated. Titanium alloy (Ti-6A1-4V) coated with BioglassR (45S5), apatite-wollastonite containing glass ceramic (AW), or beta-tricalcium phosphate (TCP) was prepared, and rectangular specimens were implanted into the tibial bones of mature male rabbits, which were sacrificed 8 or 24 weeks after implantation. The tibiae containing the implants were dissected out and subjected to detachment tests to measure the failure load. The bone-implant interface was investigated by Giemsa surface staining, contact microradiography, and scanning electron microscopy-electron probe microanalysis (SEM-EPMA). Eight weeks after implantation, the failure loads for implants coated with BioglassR, AW, and TCP were 1.04 +/- 0.94, 2.03 +/- 1.17, and 3.91 +/- 1.51 kg, respectively, and 24 weeks after implantation, the respective failure loads were 2.72 +/- 1.33, 2.39 +/- 1.30, and 4.23 +/- 1.34 kg. Failure loads of AW- and TCP-coated implants did not increase significantly with time. After the detachment test, breakage of the coating layer was observed. Bioactive ceramics can act as stimulants that induce bonding between bone and metal implants. However, failure load of metal implants coated with the bioactive ceramics was lower than that of bulk AW or TCP. It appears impossible to obtain a higher failure load using a bioactive-ceramic coating on titanium alloy. Histologically, the coating layer was found to become detached from the metal implant and the bone tissue bonded to the coating layer. SEM-EPMA observation revealed breakage of the coating layer, although bonding between bone and the coating layer was evident. A Ca-P-rich layer was observed at the interface between bone and the AW coating, and a Ca-P-rich and a Si-rich layer were observed at the interface between bone and the BioglassR coating. For clinical application, it would seem better to use coated metal implants for short-term implantation. However, there is a possibility of breakage of the coating layer because of both dissolution of the bioactive ceramic and mechanical weakness at the interface between the coating layer and the metal implant.
 ...
PMID:Bone-bonding behavior of plasma-sprayed coatings of BioglassR, AW-glass ceramic, and tricalcium phosphate on titanium alloy. 901 92

Bond coats for plasma-sprayed hydroxyapatite (HAp) coatings on Ti-6A1-4V hip endoprotheses are being developed for improved in vivo performance. Bond coat powders consisting of (i) CaO-stabilized zirconia, (ii) a eutectic composition of titania and non-stabilized zirconia, and (iii) titania were applied by atmospheric plasma spraying (APS) to Ti-6A1-4V-coupons and 100 microm-thick Ti-6A1-4V foils. Subsequently, a thick layer of HAp was sprayed onto the thin bond coats. Peel tests on Ti-6A1-4V foil/bond coat/HAp top coat assemblies revealed that titania and titania/ zirconia bond coats increased the peel adhesion strength in a statistically significant way from 22 N m(-1) (HAp without a bond coat) to >42 and 32 N m(-1), respectively. Microstructural investigations by SEM on cross-sections of coatings leached in simulated body fluid for up to 28 days led to the conclusion that the chemically very stable bond coats act as an improved chemical barrier against in vivo release of metal ions from the implant, as well as an improved adhesive bond by development of very thin well-adhering reaction layers, presumbly composed of perovskite, calcium dititanate, and/or calcium zirconate.
 ...
PMID:Development of plasma-sprayed bioceramic coatings with bond coats based on titania and zirconia. 979 27

The corrosion behaviors of Ti and Ti-6Al-4V, Ti-6Al-7Nb, Ti-0.5Pt, Ti-6Al-4V-0.5Pt, and Ti-6Al-7Nb-0.5Pt alloys were examined using an electrochemical analyzer in artificial saliva containing 0.1 and 0.2% NaF at a pH of 4.0. The SEM observations revealed that the surfaces of the alloys containing 0.5 wt% Pt were not affected in fluoride-containing environments, whereas the surfaces of Ti, Ti-6A1-4V, and Ti-6Al-7Nb alloys were markedly rough. In artificial saliva containing 0.1% NaF at a pH of 4.0, the amounts of Ti dissolved from the Ti, Ti-6Al-4V, and Ti-6Al-7Nb alloys were about 50 times larger than those of the alloys containing 0.5 wt% Pt. The tensile strengths of the alloys containing 0.5 wt% Pt were equal to or higher than those of pure Ti or the alloys without Pt. The Ti-0.5Pt, Ti-6Al-4V-0.5Pt, and Ti-6Al-7Nb-0.5 alloys are expected to be useful in clinical dentistry as new Ti alloys with high corrosion resistance and mechanical strength.
 ...
PMID:The development of Ti alloys for dental implant with high corrosion resistance and mechanical strength. 1762 43