Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0268318 (ICP)
 10,007 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

In line with recent European environmental guidelines on biomasses, one of the most important parameters to take into account is the As concentration, especially when present in biomasses and complex matrices. The goal of the present study is to give information about possible technical-analytical problems during the determinations of such elements by means of different instrumental spectroscopy techniques, in particular inductively coupled plasma atomic emission (ICP-AES) and atomic absorption (AAS), using two different wavelengths, 188.98 nm and 193.70 nm. In the Laboratory of Hygiene of National Institute of Health in Italy, a specific study has been carried out concerning the determination of As contents in environmental solid matrices, using as reference material BCR 141 R, represented by a calcareous soil. In particular, whereas recovery tests did not show particular drawbacks, difficulties were met in the As detection in reference material. Spectral interference was seen during determination by ICP-AES and matrix interference during determination by AAS, in particular using ETAAS with deuterium background correction and HAAS. Using ETAAS with Zeeman background correction at 193.70 nm, the As line did not show particular matrix interference during the reading of samples.A ring test involving two more laboratories and another certified reference material (IAEA-356 in marine sediment matrix) produced important information about problems of under/over estimation of data. Two different instrumental techniques, ICP-MS and HAAS, confirmed previous data, i.e., overestimation for inductively coupled plasma mass spectrometry and that As values achieved by HAAS were of the same order as the references, but affected by considerable standard deviation. In the light of this study, data achieved on the environmental matrices investigated suggest that the critical step in As determination is the instrumental reading, rather than the mineralization process. Further, each of the methods proposed, apart from ETAAS with Zeeman background correction, presents its own peculiar drawbacks and no particular advantage over other techniques.
 ...
PMID:Determination of As in environmental solid matrix. 1247 90

Inductively coupled plasma mass spectrometry (ICP-MS) is used for phosphorus determination in protein samples. A small amount of solid protein sample (down to 1 micro g) or digest (1-10 micro L) protein solution was denatured in nitric acid and hydrogen peroxide by closed-microvessel microwave digestion. Phosphorus determination was performed with an optimized analytical method using a double-focusing sector field inductively coupled plasma mass spectrometer (ICP-SFMS) and quadrupole-based ICP-MS (ICP-QMS). For quality control of phosphorus determination a certified reference material (CRM), single cell proteins (BCR 273) with a high phosphorus content of 26.8+/-0.4 mg g(-1), was analyzed. For studies on phosphorus determination in proteins while reducing the sample amount as low as possible the homogeneity of CRM BCR 273 was investigated. Relative standard deviation and measurement accuracy in ICP-QMS was within 2%, 3.5%, 11% and 12% when using CRM BCR 273 sample weights of 40 mg, 5 mg, 1 mg and 0.3 mg, respectively. The lowest possible sample weight for an accurate phosphorus analysis in protein samples by ICP-MS is discussed. The analytical method developed was applied for the analysis of homogeneous protein samples in very low amounts [1-100 micro g of solid protein sample, e.g. beta-casein or down to 1 micro L of protein or digest in solution (e.g., tau protein)]. A further reduction of the diluted protein solution volume was achieved by the application of flow injection in ICP-SFMS, which is discussed with reference to real protein digests after protein separation using 2D gel electrophoresis.The detection limits for phosphorus in biological samples were determined by ICP-SFMS down to the ng g(-1) level. The present work discusses the figure of merit for the determination of phosphorus in a small amount of protein sample with ICP-SFMS in comparison to ICP-QMS.
 ...
PMID:Determination of phosphorus in small amounts of protein samples by ICP-MS. 1261 Jul 11

A species-specific isotope dilution (ID) method is described for the determination of mono-, di, and tri-butyltin compounds in sediment by gas chromatography-inductively coupled plasma mass spectrometry (GC-ICP-MS), where the mixture of 118Sn-enriched butyltin compounds synthesized in our laboratory was used as a spike. A correction method for the mass bias, a quantitative extraction of the butyltins from sediment, and an assay for the concentration of the standard solution for the reverse ID procedure were investigated to achieve a reliable ID analysis. The spike solution was added with tri-propyltin (TPrT), and the butyltins were extracted by mechanical shaking into acetic acid-tropolone-toluene. The extracted butyltins were ethylated with sodium tetraethylborate and measured by GC-ICP-MS. The mass bias correction factor for the butyltins was calculated with the measured area ratio of 120Sn/118Sn of TPrT in each chromatographic run, and the correction was carried out. The mass bias was well corrected with this in-run correction (the standard uncertainties of the corrected 120Sn/118Sn for the butyltins were in the range 0.03-0.45%, typically 0.25%, with triplicate measurement corresponding to 0.02-0.37% mass bias). The extraction efficiency of mono-butyltin (MBT) from sediment was improved by using tropolone-toluene as the solvent. Well-defined standard solutions for the reverse-ID procedure could be obtained by an assay for the purities of the natural abundance butyltin chloride reagents used for preparing the standard solutions. Overall uncertainties associated with the present method were estimated, where the sediment certified reference materials, PACS-2 and BCR 646, were analyzed. The uncertainty arising from the extraction was the main contributor to the overall uncertainties for MBT and di-butyltin (DBT) determinations, while with the case of tri-butyltin (TBT) determination the uncertainties arising from the purity of TBT chloride reagent used for preparing the standard solution was a large contributor to the overall uncertainties although the uncertainty arising from the extraction was also a main contributor. The analytical results of MBT, DBT, and TBT in both reference materials, except for MBT results in PACS-2, were in good agreement with the certified values in each. The result of MBT in PACS-2 (0.677 +/- 0.049 microg g(-1) as tin, mean +/- expanded uncertainty) was significantly higher than the certified value (0.45 +/- 0.05 microg g(-1)), but closely matched with the lately reported values (Rajendran, Tao, Nakazato and Miyazaki, Analyst, 2000, 125, 1757: 0.62 +/- 0.02 microg g(-1); Chiron, Roy, Cottier and Jeannot, J. Chromatogr. A, 2000, 879, 137: 0.634 +/- 0.082 microg g(-1); Alonso, Encinar, Gonzalez and Sanz-Medal, Anal. Bioanal. Chem., 2002, 373, 432: 0.64 +/- 0.04 microg g(-1). The present method is concluded to be reliable for the determination of MBT, DBT, and TBT in sediment.
 ...
PMID:Species-specific isotope dilution analysis of mono-, di, and tri-butyltin compounds in sediment using gas chromatography-inductively coupled plasma mass spectrometry with synthesized 118Sn-enriched butyltins. 1270 86

A novel reversed phase ion-pair micro HPLC system with on-line fluorescence detection has been developed systematically and studied for the determination of cadmium in its bio-available fractions of soil samples. In this system, a micro ODS column of 1.0 mm i.d.x150 mm length and a mobile phase containing 6 mmol L(-1) 8-hydroxyquinoline 5-sulphonic acid (HQS), 3 mmol L(-1) cetyltrimethylammonium bromide (CTMABr), 10 mmol L(-1) acetic acid-acetate buffer (pH 5.1) as well as 50% acetonitrile at 50 microL min(-1) flow rate were employed to determine cadmium with a 2 microL flow cell through its fluorescence at 518 nm under 338 nm excitation. Furthermore, the composition of Cd-HQS chelate formed on the column was confirmed to be [Cd(HQS)(2)](2-) through a log-log plot method, and then combined with the ion-pair reagent by the electrostatic force under the chromatographic condition proposed. With such a method, the detection limit of cadmium was 8.48 ng mL(-1) (3sigma) with 1 microL sample injection, and the linear range for the determination of cadmium was 30-800 ng mL(-1) (R(2)=0.992). This method has been successfully applied to determination of cadmium in its bio-available fractions of BCR-483 and soil samples without interference from other coexistent metal ions. The RSD (n=6) was less than 7.3%. The results were in agreement with the indicative value for BCR-483 and those for the soil samples obtained by ICP-MS with a pretreatment of bis(1,1,3,3-tetramethylbutyl) phosphinic acid extraction.
 ...
PMID:Chromatographic behavior of cadmium in an ion-pair reversed-phase micro HPLC system and its application to the determination of bio-available cadmium in soil samples. 1280 67

This paper reports the assessment of total arsenic and six arsenic species (As(III), As(V), MMA, DMA, AsBet, AsCol) as contaminants of mussel samples collected around the island of Sardinia and in the Gulf of Venice. The samples were analysed using cation- and anion-exchange HPLC-HG-AFS for speciation and ICP-AES for the total As determination. To ensure the robustness of the routine analytical method, the technique was validated using a candidate reference material, BCR-710, and good agreement was obtained. It was recognised that higher total arsenic concentration in mussels does not necessarily result in higher toxicity of mussel samples.
 ...
PMID:The potential of arsenic speciation in molluscs for environmental monitoring. 1282 32

A European directive was recently adopted limiting the use of hazardous substances such as Pb, Hg, Cd, and Cr(VI) in vehicle manufacturing. From July 2003 a maximum of 2 g Cr(VI) will be authorised per vehicle in corrosion-preventing coatings of key components. As no standardised procedures are available to check if produced vehicles are in agreement with this directive, the objective of this work was to develop analytical procedures for total chromium and Cr(VI) determination in these materials. The first step of this study was to optimise digestion procedures for total chromium determination in plastic and metallic materials by inductively coupled plasma mass spectrometry (ICP-MS). High resolution (HR) ICP-MS was used to examine the influence of polyatomic interferences on the detection of the (52)Cr(+) and (53)Cr(+) isotopes. If there was strong interference with m/ z 52 for plastic materials, it was possible to use quadrupole ICP-MS for m/ z 53 if digestions were performed with HNO(3)+H(2)O(2). This mixture was also necessary for digestion of chromium from metallic materials. Extraction procedures in alkaline medium (NH(4)(+)/NH(3) buffer solution at pH 8.9) assisted by sonication were developed for determining Cr(VI) in four different corrosion-preventing coatings by HPLC-ICP-MS. After optimisation and validation with the only solid reference material certified for its Cr(VI) content (BCR 545; welding dusts), the efficiency of this extraction procedure for screw coatings was compared with that described in the EN ISO 3613 standard generally used in routine laboratories. For coatings comprising zinc and aluminium passivated in depth with chromium oxides the extraction procedure developed herein enabled determination of higher Cr(VI) concentrations. This was also observed for the screw covered with a chromium passivant layer on zinc-nickel. For coating comprising a chromium passivant layer on alkaline zinc the standardized extraction procedure was more efficient. In the case of painted metallic plate, because of a reactive matrix towards Cr(VI), its extraction without degradation was difficult to perform.
 ...
PMID:Development of analytical procedures for determination of total chromium by quadrupole ICP-MS and high-resolution ICP-MS, and hexavalent chromium by HPLC-ICP-MS, in different materials used in the automotive industry. 1290 54

Results are shown obtained in the optimization of an automatic flow injection system that combines microwave digestion with atomic spectrometric detection (FAAS, ICP/AES) for the determination of heavy metals in sewage sludge. Digestion is performed by preparing a suspension of the sample in 1.5 mol/l HNO(3) and making it flow through a PTFE capillary tube placed inside a conventional microwave oven. The effects of the length and inner diameter of the capillary tube, as well as that of the pumping rate, have been studied in order to find the experimental conditions that allow a quantitative elemental recovery in the shortest period of time possible. The optimization study was carried out on a certified sample (BCR No. 146), and the elements determined were Zn, Cu, Pb, Cd, Ni and Cr. The experimental data (percent recovery vs. digestion time) have been fitted to a mathematical model in order to quantify the influence of each of the variables studied. The optimized procedure (MW-ICP/AES) has been applied to one ordinary and one certified sewage sludge sample. In comparison with the conventional methods of sewage sludge analysis, the one proposed is less time consuming, while being equally precise and accurate.
 ...
PMID:Automatic flow-injection system for the determination of heavy metals in sewage sludge by microwave digestion and detection by inductively coupled plasma-atomic emission spectrometry (MW-ICP/AES). 1504 33

An analytical procedure for total arsenic and arsenic species quantification in marine organisms has been developed. Fresh materials are freeze-dried and reduced to powders before analysis. Arsenic is determined either by energy dispersive X-ray fluorescence (EDXRF) directly or by inductively coupled plasma optical emission spectrometry (ICP/OES) after microwave digestion. Arsenic speciation is performed on the extracted sample using liquid chromatography coupled to ICP/OES for arsenobetaine and arsenocholine determination and to the hydride generation-quartz furnace atomic absorption spectrometric technique for arsenite, arsenate, monomethylarsonic and dimethylarsinic acids quantification. Special precautions are taken to avoid losses or contaminations as well as to prevent analytical errors during the quantification stage. Other methods are applied and the corresponding results compared for each step of the procedure. The method is finally validated by means of intercomparison studies within the Measurements and Testing Programme of the European Community (formely BCR).
 ...
PMID:Arsenic speciation in marine organisms: from the analytical methodology to the constitution of reference materials. 1506 44

Inductively coupled plasma isotope-dilution mass spectrometry (ICP-IDMS) with direct injection of isotope-diluted samples into the plasma, using a direct injection high-efficiency nebulizer (DIHEN), was applied for accurate sulfur determinations in sulfur-free premium gasoline, gas oil, diesel fuel, and heating oil. For direct injection a micro-emulsion consisting of the corresponding organic sample and an aqueous 34S-enriched spike solution with additions of tetrahydronaphthalene and Triton X-100, was prepared. The ICP-MS parameters were optimized with respect to high sulfur ion intensities, low mass-bias values, and high precision of 32S/34S ratio measurements. For validation of the DIHEN-ICP-IDMS method two certified gas oil reference materials (BCR 107 and BCR 672) were analyzed. For comparison a wet-chemical ICP-IDMS method was applied with microwave-assisted digestion using decomposition of samples in a closed quartz vessel inserted into a normal microwave system. The results from both ICP-IDMS methods agree well with the certified values of the reference materials and also with each other for analyses of other samples. However, the standard deviation of DIHEN-ICP-IDMS was about a factor of two higher (5-6% RSD at concentration levels above 100 mircog g(-1)) compared with those of wet-chemical ICP-IDMS, mainly due to inhomogeneities of the micro-emulsion, which causes additional plasma instabilities. Detection limits of 4 and 18 microg g(-1) were obtained for ICP-IDMS in connection with microwave-assisted digestion and DIHEN-ICP-IDMS, respectively, with a sulfur background of the used Milli-Q water as the main limiting factor for both methods.
 ...
PMID:Accurate determination of sulfur in gasoline and related fuel samples using isotope dilution ICP-MS with direct sample injection and microwave-assisted digestion. 1523 70

Inductively coupled plasma isotope dilution mass spectrometry (ICP-IDMS) with direct laser-assisted introduction of isotope-diluted samples into the plasma, using a laser ablation system with high ablation rates, was developed for accurate sulfur determinations in different petroleum products such as 'sulfur-free' premium gasoline, diesel fuel, and heating oil. Two certified gas oil reference materials were analyzed for method validation. Two different 34S-enriched spike compounds, namely, elementary sulfur dissolved in xylene and dibenzothiophene in hexane, were synthesized and tested for their usefulness in this isotope dilution technique. The isotope-diluted sample was adsorbed on a filter-paper-like material, which was fixed in a special holder for irradiation by the laser beam. Under these conditions no time-dependent spike/analyte fractionation was only observed for the dibenzothiophene spike during the laser ablation process, which means that the measured 34S/32S isotope ratio of the isotope-diluted sample remained constant-a necessary precondition for accurate results with the isotope dilution technique. A comparison of LA-ICP-IDMS results with the certified values of the gas oil reference materials and with results obtained from ICP-IDMS analyses with wet sample digestion demonstrated the accuracy of the new LA-ICP-IDMS method in the concentration range of 9.2 microg g(-1) ('sulfur-free' premium gasoline) to 10.4 mg g(-1) (gas oil reference material BCR 107). The detection limit for sulfur by LA-ICP-IDMS is 0.04 microg g(-1) and the analysis time is only about 10 min, which therefore also qualifies this method for accurate determinations of low sulfur contents in petroleum products on a routine level.
 ...
PMID:Isotope dilution ICP-MS with laser-assisted sample introduction for direct determination of sulfur in petroleum products. 1605 50


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>