Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0267964 (PAA)
 2,561 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

This paper compares the influence of the molecular weight of polylelectrolytes forming polyelectrolyte multilayers (PEM) on wood fibers on adhesion and paper strength. Sheets were made from fibers treated with poly(allylamine hydrochloride) (PAH)/poly(acrylic acid) (PAA) of molecular mass 70,000 and 240,000, respectively, and of poly(dimethyldiallylammonium chloride) (PDADMAC)/poly(styrene sulfonate) (PSS) of molecular mass 30,000 and 80,000, respectively. The results were compared to what has recently been reported for PEM formation on fibers using a low-molecular-mass combination of PAH and PAA and a high-molecular-mass combination of PDADMAC/PSS. There was a less significant improvement in the case of the low-molecular-mass PDADMAC/PSS and the high-molecular-mass PAH/PAA. The adsorbed amounts of PAH and PDADMAC were also determined, showing a lower adsorbed amount of the low-molecular-mass PAH than of the high-molecular-mass PDADMAC. The amount of low-molecular-mass PDADMAC was similar to that found for high-molecular-mass PDADMAC/PSS. Individual fibers were partly treated and studied, showing a less significant decrease in wettability with low-molecular-mass PDADMAC/PSS than with the high-molecular-mass combination. The effect of the molecular weight on the adhesion was discussed in terms of the structure and wettability of the PEMs.
 ...
PMID:Polyelectrolyte multilayers on wood fibers: influence of molecular weight on layer properties and mechanical properties of papers from treated fibers. 1884 50

Positively charged poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) complexes (noted as PAH-PAA) with a molar excess of PAH were layer-by-layer (LbL) assembled with polyanion poly(sodium 4-styrenesulfonate) (PSS) to produce multilayer films. The film structure and deposition behavior of the PAH-PAA/PSS films were influenced by the structure of PAH-PAA complexes in solution. For the PAH-PAA complexes with a low ratio of PAA to PAH the PAH-PAA complexes have low-level cross-linking and are flexible. The resultant PAH-PAA/PSS films have a thin film thickness and smooth surface and exhibit a nonlinear deposition behavior where the amount of PAH-PAA complexes and PSS deposited in each deposition cycle are larger than in its previous cycle. The PAH-PAA complexes with a high ratio of PAA to PAH have high-level cross-linking and are rigid. The PAH-PAA/PSS films constructed from the rigid PAH-PAA complexes have a large film thickness and rough surface and exhibit a linear deposition behavior. Deposition of the PAH-PAA/PSS films was well characterized by quartz crystal microbalance, atomic force microscopy, and scanning electron microscopy. The thermally cross-linked PAH-PAA/PSS films can be released from substrate to form stable free-standing films by an ion-triggered exfoliation method. Meanwhile, positively charged PAH-PAA complexes can be LbL assembled with negatively charged PAH-PAA complexes with a molar excess of PAA to produce multilayer films. Use of polyelectrolyte-polyelectrolyte complexes as building blocks for LbL fabrication provides a facile way to tailor the structures of the resultant films by simply changing the structure of the complexes in solution.
 ...
PMID:Layer-by-layer deposition of polyelectrolyte-polyelectrolyte complexes for multilayer film fabrication. 1910 38

Both hyaluronan (HA) and chitosan (CHI) are biocompatible polysaccharide electrolytes. The multilayers formed by these polyelectrolytes alone are known to be rather soft and strongly viscoelastic. In this work we study multilayers formed by incorporating synthetic nonsaccharide polyelectrolytes such as polyallylamine (PAH) and poly(acrylic acid) (PAA) in various proportions into the HA/CHI layers. The buildup was followed on a quartz crystal resonator. Surface acoustic impedance recorded in these measurements, in suitable conditions, gives a spiral when plotted in the complex plane. The shape of this spiral depends on the viscoelasticity of the layer material and regularity of the growth process. We found that poly(acrylic acid) destroys the soft diffuse matrix formed by hyaluronan. It forms diffusion barriers when deposited sparsely between the layers. If its proportion is higher, the film growth adopts a linear buildup in the layer-by-layer process. The linear buildup of CHI/PAA reveals that the buildup regime of a multilayer film does not determine the viscoelastic properties of the film. Linearly and exponentially growing films may have very similar mechanical properties. Polyacrylic acid forms a kind of scaffold inside the film giving the natively soft hyaluronan/chitosan film more mechanical strength. The optimal combination gave more than 100-fold increase in the shear modulus.
 ...
PMID:Influence of synthetic polyelectrolytes on the growth and properties of hyaluronan-chitosan multilayers. 1911 71

We demonstrate that patterned nanodots can be obtained from alternatively self-assembled polyelectrolytes which consist of poly(acrylic acid) (PAA) and poly(allylamine hydrochloride) (PAH) by using atomic force microscopy. The surface potentials are easily reversible as positive or negative depending on the kind of the top polyelectrolyte layer. With the layer by layer growth, the nanodots are formed exactly on the charged area and their thicknesses proportionally increase to the total number of monolayers with a uniform thickness of about 0.5 nm.
 ...
PMID:Formation of self-assembled polyelectrolyte multilayer nanodots by scanning probe microscopy. 1915 32

The release of alpha,beta,gamma,delta-tetrakis(4-N-methylpyridyl)porphyrin (TMPyP) from layer-by-layer assembled thin films composed of poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) was electrochemically controlled. The release rate of TMPyP was enhanced when a positive electrode potential (+1.2 to +1.5 V) was applied to the glassy carbon electrode on which TMPyP-loaded PAH/PAA film was coated, while the effect of lower electrode potentials (0 to +1.0 V) was negligibly small. The effect of applied potential on the release rate was more significant at pH 7.4 than in the solutions of pH 8.0 and 9.0. The electrochemically enhanced release of TMPyP was rationalized based on local pH change in the vicinity of the electrode surface, which was induced by electrolysis of H(2)O.
 ...
PMID:Electrochemically controlled release of alpha,beta,gamma,delta-tetrakis(4-N-methylpyridyl)porphine from layer-by-layer thin films. 1921 20

SiO(2) nanoparticles capped with gamma-aminopropyltrimethoxysilane were doped into polyelectrolyte (poly(allylamine hydrochloride), PAH, and poly(acrylic acid), PAA) multilayer films via spin-assisted layer-by-layer self-assembly. The resulting as-prepared multilayer films were heated at a proper temperature to generate cross-linked composite films with increased adhesion to substrates. The tribological behavior of the multilayer films was evaluated on a microtribometer. It was found that SiO(2)-doped composite films had better wear resistance than pure polyelectrolyte multilayers, possibly because doped SiO(2) nanoparticles were capable of enhancing load-carrying capacity and had "miniature ball bearings" effect. Moreover, heat-treatment had significant effect on the morphology of the composite films. Namely, heat-treated (SiO(2)/PAA)(9) film had a larger roughness than the as-prepared one, due to heat-treatment-induced agglomeration of SiO(2) nanoparticles and initiation of defects. However, heat-treated (PAH/PAA)(3)/(SiO(2)/PAA)(3)(PAH/PAA)(3) film had greatly reduced roughness than the as-prepared one, and it showed considerably improved wear resistance as well. This could be closely related to the "sandwich-like" structure of the composite multilayer film. Namely, the outermost strata of composite multilayer film were able to eliminate defects associated with the middle strata, allowing nanoparticles therein to maintain strength and robustness while keeping soft and fluid-like exposed surface. And the inner strata were well anchored to substrate and acted as an initial "bed" for SiO(2) nanoparticles to be inhabited, resulting in good antiwear ability.
 ...
PMID:Preparation and characterization of layer-by-layer self-assembled polyelectrolyte multilayer films doped with surface-capped SiO2 nanoparticles. 1926 21

Cationic contact-killing is an important strategy for creating antimicrobial surfaces that prevent viable bacteria attachment. Recent studies have shown that highly swollen, compliant surfaces resist bacterial attachment and a sufficient density of mobile cationic charge can effectively disrupt bacterial cell membranes. Polyelectrolyte multilayers (PEMs), a popular coating system for surface modification, have been used to kill bacteria through the incorporation of contact-killing or leaching biocides. In this work, we show that manipulation of multilayer assembly and postassembly conditions (e.g., pH) to expose mobile cationic charge can create antimicrobial PEMs without the addition of specific biocidal species. As a model system, we explored PEMs comprising poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrene sulfonate) (SPS) assembled at high pH and subsequently immersed in low pH solutions. This system undergoes a reversible pH-dependent swelling transition, and we demonstrate that antimicrobial functionality at physiological pH conditions can be turned on and off with suitable pH treatment. In both airborne and waterborne bacteria assays, the viability of two strains of Gram positive Staphylococcus epidermidis (S. epidermidis), one biofilm forming and one nonbiofilm forming, and two strains of Gram negative Escherichia coli (E. coli) was effectively reduced on SPS/PAH multilayers displaying accessible cationic charge. To generalize our results, the pH assembly conditions of PEMs comprising poly(acrylic acid) (PAA) and PAH were also modified to introduce antibacterial capabilities.
 ...
PMID:Polyelectrolyte multilayers with intrinsic antimicrobial functionality: the importance of mobile polycations. 1931 89

Integration of living cells with novel microdevices requires the development of innovative technologies for manipulating cells. Chemical surface patterning has been proven as an effective method to control the attachment and growth of diverse cell populations. Patterning polyelectrolyte multilayers through the combination of layer-by-layer self-assembly technique and photolithography offer a simple, versatile, and silicon compatible approach that overcomes chemical surface patterning limitations, such as short-term stability and low-protein adsorption resistance. In this study, direct photolithographic patterning of two types of multilayers, PAA (poly acrylic acid)/PAAm (poly acryl amide) and PAA/PAH (poly allyl amine hydrochloride), were developed to pattern mammalian neuronal, skeletal, and cardiac muscle cells. For all studied cell types, PAA/PAAm multilayers behaved as a cytophobic surface, completely preventing cell attachment. In contrast, PAA/PAH multilayers have shown a cell-selective behavior, promoting the attachment and growth of neuronal cells (embryonic rat hippocampal and NG108-15 cells) to a greater extent, while providing little attachment for neonatal rat cardiac and skeletal muscle cells (C2C12 cell line). PAA/PAAm multilayer cellular patterns have also shown a remarkable protein adsorption resistance. Protein adsorption protocols commonly used for surface treatment in cell culture did not compromise the cell attachment inhibiting feature of the PAA/PAAm multilayer patterns. The combination of polyelectrolyte multilayer patterns with different adsorbed proteins could expand the applicability of this technology to cell types that require specific proteins either on the surface or in the medium for attachment or differentiation, and could not be patterned using the traditional methods.
 ...
PMID:Patterning of diverse mammalian cell types in serum free medium with photoablation. 1933 91

Layer-by-layer (LbL) assembled organic-inorganic poly(acrylic acid) (PAA)/poly(allylamine hydrochloride) (PAH)/ Au nanoparticle hybrid films are patterned by using Norland Optical Adhesive 63 (NOA 63) polymer molds. Depending on the rigidity of the hybrid films, their patterning can be realized by a room-temperature imprinting or lift-off process. For [(PAA/PAH)1-(Au nanoparticle/PAH)3]*10 and [(PAA/PAH)3-(Au nanoparticle/PAH)3]*5 films which have a low content of Au nanoparticles, the films can be imprinted at room temperature to form patterned films with large areas because of the compressibility and fluidity of the films under high pressure. The Au nanoparticle/PAH films, which have an extremely high content of Au nanoparticles and are fragile, can be patterned by a lift-off process during which the film contacted with the NOA 63 mold was peeled off because of the strong adhesion between the film and the mold and the fragility of the film. The complementary room-temperature imprinting and lift-off methods with polymer NOA 63 molds provide facile and general ways to pattern LbL assembled organic-inorganic films with various film compositions.
 ...
PMID:Patterning of layer-by-layer assembled organic-inorganic hybrid films: imprinting versus lift-off. 1943 92

We developed a cell-based assay based on the spin-assisted layer-by-layer (LbL) assembled polyelectrolyte matrix platforms. Three types of human breast epithelial cell lines including normal cells (184B5), noncancerous fibrocystic disease cells (MCF 10F), and metastatic cancerous cells (CAMA-1) were cultured, analyzed, and compared in parallel on various LbL-assembled polymer films. Poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) electrolyte polymers were used as the basic building units to form various LbL polyelectrolyte matrices. The mechanical rigidity, surface charge, and biorecognition property of the LbL platforms were controlled by tailoring the LbL surface, thermal cross-linking, and protein modification. Cellular phenotypic changes in adhesion, proliferation, and morphology on these LbL films were characterized and analyzed for the three different cell types. Our analysis results indicate that the cellular phenotype can be controlled by taking advantage of different surface charge, mechanical property, and biological modification (i.e., fibronectin in this case) of the LbL multilayer platforms. Importantly, cell phenotypical quantification results show that the cell spreading area per cell and optical density are useful parameters in distinguishing metastatic cancer cells from normal or fibrocystic disease cells on these LbL films. These LbL-based cell assay platforms have a potential for the development of various disease diagnostic cell assays.
 ...
PMID:Tunable layer-by-layer polyelectrolyte platforms for comparative cell assays. 1957 97


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>