Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0019270 (hernia)
 15,856 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

This study utilized spectral and thermal analysis of explanted hernia mesh materials to determine material inertness and elucidate reasons for hernia mesh explantation. Composite mesh materials, comprised of polypropylene (PP) and expanded polytetrafluoroethylene (ePTFE) mesh surrounded by a polyethylene terephthalate (PET) ring, were explanted from humans. Scanning electron microscopy (SEM) was conducted to visually observe material defects while attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) was used to find chemical signs of surface degradation. Modulated differential scanning calorimetry (MDSC) and thermogravimetric analysis (TGA) gave thermal stability profiles that showed changes in heat of fusion and rate of percent weight loss, respectively. ATR-FTIR scans showed higher carbonyl peak areas as compared to pristine for 91% and 55% of ePTFE and PP explants, respectively. Ninety-one percent of ePTFE explants also exhibited higher C--H stretch peak areas. Seventy-three percent of ePTFE explants had higher heats of fusion while 64% of PP explants had lower heats of fusion with respect to their corresponding pristines. Only 9% of PET explants exhibited a lower heat of fusion than pristine. Seventy-three percent of ePTFE explants, 73% of PP explants, and only 18% of PET explants showed a decreased rate of percent weight loss as compared to pristine. The majority of the PP and ePTFE mesh explants demonstrated oxidation and crosslinking, respectively, while the PET ring exhibited breakdown at the sites of high stress. The results showed that all three materials exhibited varied degrees of chemical degradation suggesting that a lack of inertness in vivo contributes to hernia mesh failure.
 ...
PMID:Materials characterization of explanted polypropylene, polyethylene terephthalate, and expanded polytetrafluoroethylene composites: spectral and thermal analysis. 2057 29

A new type of polypropylene (PP) hernia mesh, modified with poly(L-lactic acid) (PLLA), was developed and used to repair rat abdominal wall defect. The PP mesh was first treated with oxygen plasma and then grafted with PLLA in phosphorus pentachloride (PCl5 ) solution in dichloride methane. The water contact angle changed during the procedure, and the coverage percentage of PLLA on the PP was about 80%. ATR-FTIR spectroscopy measurements showed the existence of carbonyl group absorption peak (1756.9 cm(-1) ), and atomic force microscope and scanning electron microscope morphological observation indicated that the surface of the PP mesh was covered with PLLA graft. X-ray photoelectron spectroscopy spectra was used to probe chemical group changes and confirmed that the PLLA was grafted onto the PP. A total of 36 Sprague-Dawley rats were randomly divided into six groups, and they received either modified meshes (experimental groups) or PP meshes (control groups) to repair abdominal wall defects. All animals survived until the end of the experiment. Rats in each group were dissected after the operation (after 1 week, 2 weeks, and 1 month, respectively), and the adhesion effects were evaluated. Sections of the mesh parietal peritoneum overlap were examined histologically and graded for inflammation reaction. Compared with the control groups, the experimental groups showed a better ability to resist peritoneal cavity adhesions (P < 0.05), and there was no increase in inflammation formation (P > 0.05). This new type of PLLA-modified PP mesh displayed an additional property of antiadhesion in animal abdominal wall defect repair.
 ...
PMID:Preparation of poly(L-lactic acid)-modified polypropylene mesh and its antiadhesion in experimental abdominal wall defect repair. 2366 68