Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0015672 (fatigue)
 51,768 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

Cyclic fatigue of nickel-titanium, engine-driven instruments was studied by determining the effect of canal curvature and operating speed on the breakage of Lightspeed instruments. A new method of canal curvature evaluation that addressed both angle and abruptness of curvature was introduced. Canal curvature was simulated by constructing six curved stainless-steel guide tubes with angles of curvature of 30, 45, or 60 degrees, and radii of curvature of 2 or 5 mm. Size #30 and #40 Light-speed instruments were placed through the guide tubes and the heads secured in the collet of a Mangtrol Dynamometer. A simulated operating load of 10 g-cm was applied. Instruments were able to rotate freely in the test apparatus at speeds of 750, 1300, or 2000 rpm until separation occurred. Cycles to failure were determined. Cycles to failure were not affected by rpm. Instruments did not separate at the head, but rather at the point of maximum flexure of the shaft, corresponding to the midpoint of curvature within the guide tube. The instruments with larger diameter shafts, #40, failed after significantly fewer cycles than did #30 instruments under identical test conditions. Multivariable analysis of variance indicated that cycles to failure significantly decreased as the radius of curvature decreased from 5 mm to 2 mm and as the angle of curvature increased greater than 30 degrees (p < 0.05, power = 0.9). Scanning electron microscopic evaluation revealed ductile fracture as the fatigue failure mode. These results indicate that, for nickel-titanium, engine-driven rotary instruments, the radius of curvature, angle of curvature, and instrument size are more important than operating speed for predicting separation. This study supports engineering concepts of cyclic fatigue failure and suggests that standardized fatigue tests of nickel-titanium rotary instruments should include dynamic operation in a flexed state. The results also suggest that the effect of the radius of curvature as an independent variable should be considered when evaluating studies of root canal instrumentation.
 ...
PMID:Cyclic fatigue testing of nickel-titanium endodontic instruments. 922 Jul 35

The goal of this study was to examine the effects of absolute/relative loads and frequency on the fatigue life of titanium and stainless steel posterior spinal constructs, and to determine the failure fracture modes. The stainless steel constructs had higher stiffness and yield strength than the titanium constructs, but the ultimate static strength was almost equal for both types of constructs. Titanium constructs, however, exhibited higher variability than the stainless steel constructs. In fatigue tests, the stainless steel constructs were significantly affected by the external load and were frequency independent. It appears from fatigue curves that 500 N can be approximated as the endurance limit for the stainless steel constructs. Titanium constructs were load-frequency dependent, and their endurance limit was somewhere between the 500 and 750 N load levels. There were no differences in performance between the stainless steel and titanium constructs at 16 Hz. At 4 Hz, titanium constructs performed as well or better than stainless steel constructs. Also, the titanium constructs resulted in better performance than the stainless steel constructs in the elastic region, and with smaller differences in the plastic region. Most of the failure modes for stainless steel constructs were in screw bending at 16 Hz with a smaller percentage of rod fractures at high loads, with a higher percentage of rod fractures observed for the stainless steel constructs at 4 Hz. Most of the failure modes for titanium constructs occurred in screw bending or fracture.
 ...
PMID:Biomechanical assessment of titanium and stainless steel posterior spinal constructs: effects of absolute/relative loading and frequency on fatigue life and determination of failure modes. 943 11

The performance of any material in the human body is controlled by two sets of characteristics: biofunctionality and biocompatibility. With the wide range of materials available in the mid-1990s, it is relatively easy to satisfy the requirements for mechanical and physical functionality of implantable devices. Therefore, the selection of materials for medical applications is usually based on considerations of biocompatibility. When metals and alloys are considered, the susceptibility of the material to corrosion and the effect the corrosion has on the tissue are the central aspects of biocompatibility. Corrosion resistance of the currently used 316L stainless steel, cobalt-chromium, and titanium-based implant alloys relies on their passivation by a thin surface layer of oxide. Stainless steel is the least corrosion resistant, and it is used for temporary implants only. The titanium and Co-Cr alloys do not corrode in the body; however, metal ions slowly diffuse through the oxide layer and accumulate in the tissue. When a metal implant is placed in the human body, it becomes surrounded by a layer of fibrous tissue of a thickness that is proportional to the amount and toxicity of the dissolution products and to the amount of motion between the implant and the adjacent tissues. Pure titanium may elicit a minimal fibrous encapsulation under some conditions, whereas the proliferation of a fibrous layer as much as 2 mm thick is encountered with the use of stainless steel implants. Superior fracture and fatigue resistance have made metals the materials of choice for traditional load-bearing applications. In this review, the functionality of currently used metals and alloys is discussed with respect to stenting applications. In addition, the "shape memory" and "pseudo-elasticity" properties of Nitinol-an alloy that is being considered for the manufacturing of urologic stents-are described.
 ...
PMID:Characteristics of metals used in implants. 944 Aug 45

Nickel-titanium instruments purportedly resist deformation and loss of sharpness better than do stainless steel instruments but may be more susceptible to breakage. The processes of wear and breakage of nickel-titanium and stainless steel instruments were examined. Sixty files of five types (12 each) and three manufacturers were used. All were used repeatedly in curved canals until failure or for a maximum of 22 minutes. Each instrument was examined with scanning electron microscopy both new (control) and at spaced intervals for evidence of wear and fatigue. All new instruments were of good quality. Stainless steel instrument tended to wear the most rapidly, and next were nickel-titanium rotary instruments; the most resistant to wear were nickel-titanium hand instruments. There were few instrument separations. In general, nickel-titanium (particularly hand) instruments resisted deterioration better than did stainless steel. Nickel-titanium rotary instruments (2 of 12) had the most breakage.
 ...
PMID:Instrument deterioration with usage: nickel-titanium versus stainless steel. 947 4

Pure elemental titanium was alloyed with cobalt and chromium in dilutions of 4%, 5%, and 6% to evaluate the suitability of the resulting alloy for removable partial denture frameworks. The physical properties of the Co-Cr-Ti alloy were compared to the properties of a commercial pure titanium and Vitallium. Clasp replicas were cast in Co-Cr-Ti and Vitallium and subjected to cyclic deflection. Representative specimens from the fatigue failure tests were then evaluated using scanning electron microscopy and analyzed for elemental content. The 5% titanium dilution of cobalt-chromium proved to have the best physical properties and was used for comparison with the pure titanium and Vitallium. The Co-Cr-5% Ti had significantly better physical properties than pure titanium and a greater flexure fatigue limit than the Vitallium alloy.
 ...
PMID:Cobalt-chromium-titanium alloy for removable partial dentures. 948 40

An in vitro nondestructive fatigue test was applied to adhesive posts and cores made on endodontically treated human teeth. Five post-and-core systems were evaluated: one zircon oxide post, two titanium posts (with resinous or ceramic coating), and two resin-fiber posts. Each test specimen was intermittently loaded and thermocycled. The scanning electron microscope observation of sample sections showed that only the interfaces between restorative materials and dentin exhibited substantial deficiencies. The Komet ER (Brasseler) exhibited the greatest percentages of continuity at the coronal (83.88%) or the radicular (78.12%) dentin levels, while the Zircon experimental post presented insufficient adaptation to the radicular (21.25% continuity) and to the coronal (53.25% continuity) dentin. Seven of eight samples in the Komet group showed root fractures. The carbon-fiber post (Composipost) behaved satisfactorily (67.38% radicular continuity), in spite of the use of an older bonding agent formulation.
 ...
PMID:Adaptation of adhesive posts and cores to dentin after fatigue testing. 949 69

In this study fatigue resistance of experimentally prepared titanium-nickel (50.8% nickel and 49.2% titanium) cast clasps was evaluated in a simulated clinical situation. The change in force required to remove the titanium-nickel clasps was recorded under a repeated placement-and-removal test on steel model abutment teeth. Commercially-pure titanium, cobalt-chromium alloy, and gold-silver-palladium-copper alloy clasps were also tested for comparison. The tips of the clasps were located in the 0.25- and 0.50-mm undercut areas of the abutments. No significant changes in the retentive force were found in titanium-nickel clasps in the 1,010 repeated cycles, whereas the other three types of clasp revealed a significant decrease in the force required for removal during the test procedures (repeated analysis of variance P < 0.001). The results suggest that the cast titanium-nickel clasp may be suitable in removable prosthodontic constructions because of its significantly less permanent deformation during service. This report also discusses clinical applicability and some current problems with this new application.
 ...
PMID:Fatigue resistance of titanium-nickel alloy cast clasps. 949 76

Plates for functionally stable mandibular reconstruction are successfully introduced with biocompatible titanium. While screws have been the subject of numerous investigations, only few results are available for the mechanical stability of plates. This contribution gives an overview about experimental possibilities to test plates in tensional, bending, and torsional strength as well as fatigue, and reports results about plates made of titanium and oxygen-alloyed titanium. The alloyed material is harder, stiffer and shows higher tensile strengths. In contrast to softer titanium, contouring procedures during implantation can lead to structural defects and an associated higher fracture risk.
 ...
PMID:Mechanical strength of fracture plates made of titanium for functionally stable mandibular reconstruction. 961 94

Two clinically relevant considerations for a new bone cement are its fracture properties and flow intrusion characteristics. We present data for a titanium-fibre-reinforced poly(methyl methacrylate) (Ti-PMMA). The fracture properties presented are a concise review of previously published material, while the flow intrusion observations are new. We performed fracture toughness and fatigue fracture experiments. Two types of fatigue specimens were designed and tested. A 'smooth' specimen represented the extreme case of minimum surface flaws. The lifetime of a 'smooth' specimen incorporates fatigue crack initiation (FCI) and fatigue crack propagation (FCP). 'Notched' specimens were created by machining a sharp notch into cylindrical specimens. The sharp notch effectively eliminated FCI from a random surface flaw and thus we made the assumption that the lifetime of the notched specimen was a function of FCP only. Fatigue testing was performed on rotating-bending fatigue machines until failure. Fibre addition resulted in a significant increase in fracture toughness over the control bone cement. Fibre addition and the combination of fibre addition and centrifugation increased the fatigue crack initiation and propagation resistance of the bone cement. For the intrusion studies, eight femurs were obtained from four dogs. The femurs were prepared following a procedure similar to that in human hip replacement surgery. One of the pair of femurs from each dog was filled with non-reinforced bone cement and the other was filled with Ti-PMMA. A stainless-steel rod was inserted into the cement to simulate the insertion of a prosthesis stem. The cemented bones were sectioned and then stained with Alizarin Red S to distinguish the bone from the PMMA or Ti-PMMA. Because of the irregular bone morphology, it was not practical to quantify intrusion depth, but instead to make general observations on the intrusion characteristics. The Ti fibres did not generally flow into the small openings; however, fibre addition did not hinder the bone cement's ability to penetrate into bone interstices.
 ...
PMID:Flow intrusion characteristics and fracture properties of titanium-fibre-reinforced bone cement. 983 Sep 82

Increased use of titanium alloys as biomaterials is occurring due to their lower modulus, superior biocompatibility and enhanced corrosion resistance when compared to more conventional stainless steels and cobalt-based alloys. These attractive properties were a driving force for the early introduction of alpha (cpTi) and alpha + beta (Ti-6A1-4V) alloys as well as for the more recent development of new Ti-alloy compositions and orthopaedic metastable beta titanium alloys. The later possess enhanced biocompatibility, reduced elastic modulus, and superior strain-controlled and notch fatigue resistance. However, the poor shear strength and wear resistance of titanium alloys have nevertheless limited their biomedical use. Although the wear resistance of beta-Ti alloys has shown some improvement when compared to alpha + beta alloys, the ultimate utility of orthopaedic titanium alloys as wear components will require a more complete fundamental understanding of the wear mechanisms involved. This review examines current information on the physical and mechanical characteristics of titanium alloys used in artifical joint replacement prostheses, with a special focus on those issues associated with the long-term prosthetic requirements, e.g., fatigue and wear.
 ...
PMID:Titanium alloys in total joint replacement--a materials science perspective. 983 98


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>