Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0001511 (Adhesion)
 5,955 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

Adhesion behavior of cells to the surface of physical hydrogel membranes prepared by water-induced self-organization of precisely synthesized ABA-triblock copolymers comprised of poly(beta-benzyl L-aspartate) (PBLA) as A segment and poly(ethylene oxide) (PEO, molecular weight = 20 000) as the B segment were investigated. The cast film from the methylenechloride solution of these copolymers swelled in water very rapidly forming hydrogels (100-400% water content of total weight). The content of PBLA affected the strength, the hydrophobicity, and the amount of water involved in the hydrogel surface. During the early stage of cultivation with murine peritoneal cells, cell adhesion on the hydrogels of PEO and PBLA with 18 (20K18) and 25 (20K25) monomeric units was not observed, while adhesion on the hydrogels of PEO and PBLA with 32 (20K32) and 55 (20K55) monomeric units was successful, suggesting more than 12 mol % in PBLA content is necessary for adhesion of these cells. Although cell spreading on the hydrogels of 20K18, 20K25, and 20K32 was not sufficient, the hydrogel of 20K55 allowed cell adhesion and spreading to be bipolar with leading edge whose raffling is active with pseudopodium and lamellipodium as well as PBLA homopolymer, suggesting active motility of these cells. Remarkably, prolonged incubation restored adhesiveness onto the films at 20K18 in contrast to adhesion with 20K25 despite low hydrophobicity. It is conceivable that adaptation of proteins and chemical changes to the surface during the culture period may participate in these phenomena. Mechanical properties and interaction between cell and these copolymer hydrogels could be controlled by composition of block segments, and optimization for implants could also be attainable.
 ...
PMID:Adhesion behavior of peritoneal cells on the surface of self-assembled triblock copolymer hydrogels. 1553 62

Glass surfaces were modified by end-grafting poly(ethylene oxide) (PEO) chains having molecular weights of 526, 2000, or 9800 Da. Characterization using water contact angles, ellipsometry, and X-ray photoelectron spectroscopy confirmed the presence of the PEO brushes on the surface with estimated lengths in water of 2.8-, 7.5-, and 23.7-nm, respectively. Adhesion of two bacterial (Staphylococcus epidermidis and Pseudomonas aeruginosa) and two yeast (Candida albicans and Candida tropicalis) strains to these brushes was studied and compared to their adhesion to bare glass. For the bacterium P. aeruginosa and the yeast C. tropicalis, adhesion to the 2.8-nm brush was comparable to their adhesion on bare glass, whereas adhesion to the 7.5- and 23.7-nm brushes was greatly reduced. For S. epidermidis, adhesion was only slightly higher to the 2.8-nm brush than that to the longer brushes. Adhesion of the yeast C. albicans to the PEO brushes was lower than that to glass, but no differences in adhesion were found between the three brush lengths. After passage of an air bubble, nearly all microorganisms adhering to a brush were removed, irrespective of brush length, whereas retention of the adhering organisms on glass was much higher. No significant differences were found in adhesion nor retention between experiments conducted at 20 and those conducted at 37 degrees C.
 ...
PMID:Microbial adhesion to poly(ethylene oxide) brushes: influence of polymer chain length and temperature. 1556 45

Poly(p-xylylene) (PPX) was deposited by chemical vapor deposition (CVD) on stainless steel substrates. These PPX films were coated by solution casting of poly(lactide)-poly(ethylene oxide)-poly(lactide) triblock copolymers (PLA-PEO-PLA) loaded with 14C-labeled paclitaxel. Adhesion of PLA-PEO-PLA on PPX substrate coatings was measured using the blister test method. Excellent adhesion of the block copolymers on PPX substrates was found. Stress behavior and film integrity of PLA-PEO-PLA was compared to pure PLA on unexpanded and expanded stent bodies and was found to be superior for the block copolymers. The release of paclitaxel from the biodegradable coatings was studied under physiological conditions using the scintillation counter method. Burst release of paclitaxel was observed from PLA-PEO-PLA layers regardless of composition, but an increase in paclitaxel loading was observed with increasing content of PEO.
 ...
PMID:Coating of poly(p-xylylene) by PLA-PEO-PLA triblock copolymers with excellent polymer-polymer adhesion for stent applications. 1682 74

In tissue engineering, the nanoscale topography of the substrate is important, because transplanted cells can recognize and respond to topographical patterns, allowing control of gene expression and tissue formation. In this study, we hypothesized that the height of cell-adhesive nanoposts could regulate cell phenotype. Nano-patterned surfaces were generated via self-assembly of polystyrene-b-poly(ethylene oxide)/dodecylbenzenesulfonic acid (PS-b-PEO/DBSA) complex systems. The height of PS nanoposts, which are considered to be cell-adhesion domains, was varied from 11 to 43 nm, while nanopost size and the center-to-center distance between nanoposts were kept constant. Adhesion, growth, and differentiation of mouse preosteoblasts (MC3T3-E1) cultured on the nano-patterned surfaces were significantly influenced by nanopost height. This approach therefore holds great promise for the design of biomedical devices, as well as tissue engineering scaffolds.
 ...
PMID:The height of cell-adhesive nanoposts generated by block copolymer/surfactant complex systems influences the preosteoblast phenotype. 2545 88