Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0001511 (Adhesion)
 5,955 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

Measurements of the advancing contact angle (theta) were carried out for aqueous solution of p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycol), Triton X-100 (TX100), and Triton X-165 (TX165) mixtures on glass. The obtained results indicate that the wettability of glass depends on the concentration and composition of the surfactant mixture. The relationship between the contact angle and concentration suggests that the lowest wettability corresponds to the concentration of TX100 and TX165 and their mixture near the critical micelle concentration (CMC). The minimum of the dependence between the contact angle and composition of the mixtures for each concentration at a monomer mole fraction of TX100, alpha, equals 0.2 and 0.4 points to synergism in the wettability of the glass surface. In contrast to the results of Zisman ( Zisman, W. A. In Contact Angle, Wettability and Adhesion; Gould, R. F., Ed.; Advances in Chemistry Series 43; American Chemical Society Washington, DC, 1964; p 1 ) there was no linear dependence between cos theta and the surface tension of aqueous solutions of TX100 and TX165 mixtures for all studied systems, but a linear dependence exists between the adhesional tension and surface tension for glass, practically, in the whole concentration range of surfactants studied, the slopes of which are positive in the range of 0.43-0.67. These positive slopes indicate that the interactions between the water molecules and glass surface might be stronger than those between the surface and surfactant molecules. So, the surface excess of surfactant concentration at the glass-water interface is probably negative, and the possibility for surfactant to adsorb at the glass/water film-water interface is higher than that at the glass-water interface. This conclusion is confirmed by the values of the work of adhesion of "pure" surfactants, aqueous solutions of surfactants, and aqueous solutions of their mixtures to the glass surface and by the negative values of glass-water interfacial tension determined from the Young equation in the range of surfactant concentrations corresponding to their unsaturated monolayer at the water-air interface.
 ...
PMID:Wettability of a glass surface in the presence of two nonionic surfactant mixtures. 1857 57

This work was motivated by the unexpected values of adhesion forces measured between an atomic force microscopy tip and the hydrophobic surface of ultra-high-molecular-weight polyethylene. Two types of samples with different roughness but similar wettability were tested. Adhesion forces of similar magnitude were obtained in air and in polar liquids (water and Hank's Balanced Salt Solution, a saline solution) with the rougher sample. In contrast, the adhesion forces measured on the smoother sample in air were much higher than those measured in water or in the aqueous solution. Those experimental results suggested the presence of nanobubbles at the interface between the rough sample and the polar liquids. The existence of the nanobubbles was further confirmed by the images of the interface obtained in noncontact tapping mode. The adhesion forces measured in a nonpolar liquid (hexadecane) were small and of the same order of magnitude for both samples and their values were in good agreement with the predictions of the London-Hamaker approach for the van der Waals interactions. Finally, we correlate the appearance of nanobubbles with surface topography. The conclusion of this work is that adhesion forces measured in aqueous media may be strongly affected by the presence of nanobubbles if the surface presents topographical accidents.
 ...
PMID:Adhesion forces in liquid media: effect of surface topography and wettability. 1859 70

Adhesion forces between the calcium oxalate monohydrate (COM, whewellite) crystal and the layer of the epithelial kidney cells have been directly measured under buffer solutions by using atomic force microscope (AFM). Two renal epithelial lines, MDCK (a collecting duct line) and LLC-PK1 (a proximal tubular line), were used. All experiments were conducted in buffer solutions containing additional Ca(2+) and Mg(2+) ions in the various concentrations. For MDCK-cells, the obtained values of the adhesion force were in the range 0.12-0.51 nN and 0.12-0.20 nN for Ca(2+) and Mg(2+), respectively. No adhesion force (larger than 0.05 nN) has been found for LLC-PK1 cells. The "critical" concentrations of ions, near which the adhesion force (for MDCK-cells) was maximal, were found to be 100 mM. The "critical" concentration of ions and the tendency of the adhesion forces with the changing ions concentration, confirm earlier results of Lieske et al. [J.C. Lieske, G. Farell, S. Deganello, Urol. Res. 32 (2004) 117-123], in which the affinity (rather than the adhesion force) between the COM micro-crystals and the layer of the MDCK-cells were measured, calculating the radioactive signal of radioactive (14)C COM-crystals stuck to the cells. We believe that the aggregation of the COM crystals does not occur in the bulk urine due to short travel time through the nephron. If so, the kidney stone formation is determined by COM-seeding on the tubules walls. The further growth of the stone on the seed can take practically unlimited time because the COM crystal is practically is not soluble in water or urine solutions. The value of the adhesion force can be useful for evaluation of the adhesion energy or probability of the COM-aggregates to stick to the kidney epithelium under the urine flow. This probability is calculated taking into account the adhesion force, F(ad), and hydrodynamic driving force of the flow. This probability reflects the opportunity of the small aggregates to grow and form the kidney stones.
 ...
PMID:Direct AFM measurements of adhesion forces between calcium oxalate monohydrate and kidney epithelial cells in the presence of Ca2+ and Mg2+ ions. 1861 6

Insulin or albumin was immobilized on collagen beads using water-soluble carbodiimide. Adhesion of STO mouse fibroblast cells onto the beads decreased with increasing the amount of immobilized proteins. Growth of the cells was remarkably accelerated on the insulinimmobilized collagen beads, which can be used for serum-free cell culture. The growth acceleration became larger with increasing the amount of immobilized insulin, while it became smaller with increasing the amount of immobilized albumin. In addition, the immobilized insulin more strongly accelerated the cell growth than free insulin plus collagen beads. (c) 1995 John Wiley & Sons, Inc.
 ...
PMID:Serum-free cell culture on insulin-immobilized porous collagen beads. 1862 96

The origins for abrupt adhesion loss at a critical relative humidity (RH) for polymeric adhesives bonded to inorganic surfaces have been explored using a model poly(methyl methacrylate) (PMMA) film on glass. The interfacial and bulk water concentrations within the polymer film as a function of D 2O partial pressure were quantified using neutron reflectivity. Adhesion strength of these PMMA/SiO 2 interfaces under the same conditions was quantified using a shaft loaded blister test. A drop in adhesion strength was observed at a critical RH, and at this same RH, a discontinuity in the bulk moisture concentration occurred. The moisture concentration near the interface was higher than that in the bulk PMMA, and at the critical RH, the breadth of the interfacial water concentration distribution as a function of distance from the SiO 2/PMMA interface increased dramatically. We propose a mechanism for loss of adhesion at a critical RH based upon the interplay between bulk swelling induced stress and weakening of the interfacial bond by moisture accumulation at the PMMA/SiO 2 interface.
 ...
PMID:On the origins of sudden adhesion loss at a critical relative humidity: examination of bulk and interfacial contributions. 1868 55

In recent years, polysaccharide-based films have been developed for many applications. Some of these are in the pharmaceutical industry, where the adhesion of microorganisms to surfaces is a concern. After adhesion of a microorganism to a solid surface has taken place, the subsequent biofilm formed can act as a vehicle for spreading infections. The aim of this study is to compare the bacterial adhesion of E. coli and S. aureus from a contaminated solid model (Tryptone Soya Agar) to a range of polysaccharide-based films. These polysaccharide-based films consist of different natural starches (potato, cassava, wheat, pea and rice) and synthetic polymers hydroxyl-propyl cellulose (HPC) and carboxyl methyl cellulose (CMC)). The surface energy parameters of the films were calculated from the contact angle measurements by the sessile drop method. Apolar and polar liquids (water, formamide and hexadecane) and the Lifshitz-Van der Waals/acid-base (LW/AB) approach were used according to the method of Van Oss, Chaundhury and Good. The surface properties of the films were also correlated to the microbial adhesion. This indicated that, for both E. coli and S. aureus, the surface roughness did not affect the microbial adhesion. Only gamma(sAB) had any correlation with the microbial adhesion and gamma(sLW) was almost constant for all the various polysaccharide films tested. In addition, the electron-donor properties of the materials, exhibited via gamma(s+), were positively correlated with the adhesion of S. aureus but not with E. coli. This was in agreement with the results of the MATS (Microbial Adhesion To Solvents) test performed on the two bacteria. This revealed that only S. aureus presented an electron-acceptor characteristic.
 ...
PMID:An investigation of microbial adhesion to natural and synthetic polysaccharide-based films and its relationship with the surface energy components. 1871 4

The structure and surface chemistry of soil particles has extensive impact on many bulk scale properties and processes of soil systems and consequently the environments that they support. There are a number of physiochemical mechanisms that operate at the nanoscale which affect the soil's capability to maintain native vegetation and crops; this includes soil hydrophobicity and the soil's capacity to hold water and nutrients. The present study used atomic force microscopy in a novel approach to provide unique insight into the nanoscale properties of natural soil particles that control the physiochemical interaction of material within the soil column. There have been few atomic force microscopy studies of soil, perhaps a reflection of the heterogeneous nature of the system. The present study adopted an imaging and force measurement research strategy that accounted for the heterogeneity and used model systems to aid interpretation. The surface roughness of natural soil particles increased with depth in the soil column a consequence of the attachment of organic material within the crevices of the soil particles. The roughness root mean square calculated from ten 25 microm(2) images for five different soil particles from a Netherlands soil was 53.0 nm, 68.0 nm, 92.2 nm and 106.4 nm for the respective soil depths of 0-10 cm, 10-20 cm, 20-30 cm and 30-40 cm. A novel analysis method of atomic force microscopy phase images based on phase angle distribution across a surface was used to interpret the nanoscale distribution of organic material attached to natural and model soil particles. Phase angle distributions obtained from phase images of model surfaces were found to be bimodal, indicating multiple layers of material, which changed with the concentration of adsorbed humic acid. Phase angle distributions obtained from phase images of natural soil particles indicated a trend of decreasing surface coverage with increasing depth in the soil column. This was consistent with previous macroscopic determination of the proportions of organic material chemically extracted from bulk samples of the soils from which specimen particles were drawn. Interaction forces were measured between atomic force microscopy cantilever tips (Si(3)N(4)) and natural soil and model surfaces. Adhesion forces at humic acid free specimen surfaces (Av. 20.0 nN), which are primarily hydrophilic and whose interactions are subject to a significant contribution from the capillary forces, were found to be larger than those of specimen surfaces with adsorbed humic acid (Av. 6.5 nN). This suggests that adsorbed humic acid increased surface hydrophobicity. The magnitude and distribution of adhesion forces between atomic force microscopy tips and the natural particle surfaces was affected by both local surface roughness and the presence of adsorbed organic material. The present study has correlated nanoscale measurements with established macroscale methods of soil study. Thus, the research demonstrates that atomic force microscopy is an important addition to soil science that permits a multiscale analysis of the multifactorial phenomena of soil hydrophobicity and wetting.
 ...
PMID:Application of atomic force microscopy to the study of natural and model soil particles. 1875 93

Adhesion of the bacteria Campylobacter jejuni and Mycobacterium avium onto polyethylene terephtalate (PET), a polymer widely used within the bottled water industry was measured in two different groundwater solutions. From this, it was found that whilst the percentage cell adhesion for a given strain did not change between groundwater types, substantial variation was obtained between the two bacterial species tested: M. avium (10-30% adhered cells) and C. jejuni (1-2%) and no major variations were measured as a function of groundwater composition for a given strain. To explain this, the interfacial electro-hydrodynamic properties of the bacteria were investigated by microelectrophoresis, with the resultant data analysed on the basis of electrokinetic theory for soft biocolloidal particles. The results obtained showed that M. avium carries a significant volume charge density and that its peripheral layer exhibits limited hydrodynamic flow permeation compared to that of C. jejuni. It was also demonstrated that steric hindrance to flow penetration and the degree of hydrophobicity within/of the outer bacterial interface are larger for M. avium cells. In line with this, the larger amount of M. avium cells deposited onto PET substrates as compared to that of C. jejuni can be explained by hydrophobic attraction and chemical binding between hydrophobic PET and outer soft surface layer of the bacteria. Hydrophobicity of PET was addressed by combining contact angle analyses and force spectroscopy using CH(3)-terminated AFM tip.
Water Res 2008 Dec
PMID:Adhesion of Campylobacter jejuni and Mycobacterium avium onto polyethylene terephtalate (PET) used for bottled waters. 1892 88

Adhesion to the host surface is the first step for successful plant pathogen development and has been reported to be associated with both passive and active processes. For conidia of Venturia inaequalis, which depend on leaf wetness for germination, this process has not yet been described. Conidia of V. inaequalis adhered to wet hydrophobic surfaces immediately after contact to the surface, hours before initiation of germination. Attachment of nongerminated conidia was much better on hydrophobic surfaces, such as apple leaves and polystyrene, than on hydrophilic glass. Conidia released adhesive material localized in a droplet named spore tip glue (STG) at the spore apex which interacted with a contact surface only when water was present. Histochemical investigations indicated the presence of proteins and carbohydrates in STG, lectin labeling the presence of beta-galactose and N-acetylglucosaminyl residues. Transmission electron microscopy revealed two phases in the STG at the tip of dry mature conidia; as STG was present on the outer side of the intact fungal cell wall its formation should be associated with the secretion of glue through pores of the conidial wall. Surface-active substances affected the adhesion of conidia to hydrophobic surfaces stressing the importance of hydrophobic interactions. The use of protein biosynthesis inhibitors did not affect adhesion of conidia indicating that the adhesive material was preformed. It is concluded that the coincidence of STG, contact to a hydrophobic surface, and free water are essential for the adhesion of V. inaequalis conidia.
 ...
PMID:Localized adhesion of nongerminated Venturia inaequalis conidia to leaves and artificial surfaces. 1894 51

Adhesion is an essential parameter for stem cells. It regulates the overall cell density along the carrying surface, which further dictates the differentiation scheme of stem cells toward a more matured and specified population as well as tissue. Electronic control of the seeding density of neural stem cells (c17.2) is here reported. Thin electrode films of poly(3,4-ethylenedioxythiophene) (PEDOT):Tosylate were manufactured along the floor of cell growth dishes. As the oxidation state of the conjugated polymer electrodes was controlled, the seeding density could be varied by a factor of 2. Along the oxidized PEDOT:Tosylate-electrodes, a relatively lower density of, and less tightly bonded, human serum albumin (HSA) was observed as compared to reduced electrodes. We found that this favors adhesion of the specific stem cells studied. Surface analysis experiments, such as photoelectron spectroscopy, and water contact angle measurements, were carried out to investigate the mechanisms responsible for the electronic control of the seeding density of the c17.2 neural stem cells. Further, our findings may provide an opening for electronic control of stem cell differentiation.
 ...
PMID:Control of neural stem cell adhesion and density by an electronic polymer surface switch. 1905 38


<< Previous 1 2 3 4 5 6 7 8 9 10