Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: UMLS:C0001511 (Adhesion)
 5,955 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

The adhesion of hydroxypropyl cellulose (HPC) to well-defined solid substrates was measured as a function of dry film thickness. A well-controlled butt adhesion test, providing a constant slow rate of film detachment, was used to keep the viscoelastic contribution of the film to the adhesion measurement constant. Films were cast or sprayed from solution in either triply distilled water or absolute ethanol onto relatively smooth surfaces of poly(methyl methacrylate), poly(ethylene terephthalate), and polyethylene. A linear relationship of increasing adhesion with decreasing dry film thickness was obtained for thin films (less than 20-microns thick) on all three surfaces. An adhesion value, A0, determined by extrapolating the adhesion data to zero film thickness, was shown to be proportional to the calculated thermodynamic work of adhesion, Wa, at the film-substrate interface. No significant effect of the method of film preparation, cast or sprayed, on the adhesion measurement was noted. Adhesion for a given film thickness was greater for films prepared from solutions having a higher initial polymer concentration or when using ethanol as opposed to water as the solvent.
 ...
PMID:Adhesion of hydroxypropyl cellulose films to low energy solid substrates. 373 95

Simultaneous experiments were performed with sterilized and non-sterile water and an artificial hard water. After seeding with an environmental isolate of Legionella pneumophila numbers in the sterile and hard water decreased rapidly and colonization of various tap washer fittings failed to take place. Adhesion and growth of an environmental isolate of L. pneumophila to washers in non-sterile tap water was followed over a 4-month period with fluorescein-labelled antibody and by scanning electron microscopy. After adherence the individual cells appeared to divide to form chains which spread over the surfaces. Organisms other than legionellas were also present and a complex colonization matt was formed which was embedded in a protective coat of slime and debris. The numbers of L. pneumophila recovered from the water were highest between 4 and 7 weeks but they could still be cultivated after 4 months.
 ...
PMID:The persistence of Legionella pneumophila in non-sterile, sterile and artificial hard waters and their growth pattern on tap washer fittings. 391 60

This review of retinal pigment epithelial (RPE) physiology pays tribute to Anthony L. F. Gorman, who introduced the author to the giant neuron of Anisodoris nobilis (the sea lemon) and cellular neurobiology. The RPE is an epithelial monolayer with tight junctions, which controls the environment of the photoreceptor outer segments. The apical and basal membranes have different electrical properties and generate a standing potential across the eye. The RPE helps maintain adhesion between the retina and the wall of the eye. Adhesion is weakened by cyanide, low pH or low calcium, but enhanced by ouabain or acetazolamide. The RPE transports water from the subretinal space toward the choroid. This water movement is inhibited by hypoxia or cyanide but enhanced by ouabain or acetazolamide. The c-wave of the electroretinogram is a composite of a cornea-positive wave produced by hyperpolarization of the apical RPE membrane and a cornea-negative wave produced by the Muller cells, both in response to the fall in extracellular potassium that follows illumination of the photoreceptors. The "light response" of the standing potential is produced by depolarization of the basal membrane of the RPE. These examples illustrate how principles of cellular neurophysiology can be applied to questions of clinical relevance.
 ...
PMID:From sea lemons to c-waves. 632 7

Dissection of embalmed and untreated water buffalo carcasses (n=10) revealed that hernias had occurred at the musculotendinous junction of the diaphragm, ventral to the foramen venae cavae and slightly lateral to the median plane. The diameter of the hernial ring varied from 7 cm to 20 cm. Herniation was more common in the right thoracic cavity with the reticulum firmly adherent to the hernia ring. Adhesions between the herniated portion of the reticulum and pleura, lung, pericardium or thoracic wall were present, while in a few cases thick fibrous tracts concealing metallic bodies were found. In two cases, involvement of esophageal groove with malalignment of cardia and reticulo-omasal opening was observed. Displacement and compression of the heart was observed in four animals.
 ...
PMID:Patho-anatomy of herniation of the reticulum through the diaphragm in the bovine. 734 Sep 24

Use of porcelain denture teeth may be desirable in many clinical situations, including implant-supported prostheses. However, lack of space because of frameworks often precludes the use of conventional retention by diatorics and pins. Adhesion of porcelain denture teeth to denture resin could also stiffen and possibly strengthen dentures and decrease stain ingress between porcelain teeth and resin denture bases. Unlike previous studies that investigated the bond between conventional feldspathic metal-ceramic porcelain and bis-GMA based composite resin, this study investigated adhesion of denture tooth porcelain to polymethyl methacrylate (PMMA). High-energy air abrasion, hydrofluoric acid etching, and the use of a general purpose bonding agent resulted in an improved bond strength of heat-cured denture PMMA bonded to denture tooth porcelain. Silane coating did not improve bond strengths, and conventional air abrasion was no more effective than polishing with 600-grit silicon carbide. Storage in water and artificial aging substantially decreased bond strengths. The strongest bond strengths were achieved by a high-energy-abrasion + etching + multi-purpose bonding-agent treatment, but a simpler etching + multiple-purpose bonding-agent treatment also produced reliable results. A laboratory technique was suggested. The role of surface treatment in the mechanism of adhesion was examined with scanning electron microscopy. High-energy abrasion produced a slightly more detailed initial topography than conventional air abrasion, but after etching, the high-energy topography became much more detailed. Surface topography alone did not account for all differences found.
 ...
PMID:Adhesion of denture tooth porcelain to heat-polymerized denture resin. 747 77

An in vitro quantitative study of the adhesion of a Staphylococcus aureus strain to two types of disposable contact lenses has been carried out. The first type was an ionic/high-water-content (I-HWC) lens (42% Etafilcon A, 58% water) and the second was a non-ionic/low-water-content (Nl-LWC) lens (61.4% poly(2-hydroxyethyl methacrylate), 38.6% water). Adhesion to the two lens types was evaluated both in basic conditions and after treatment with lysozyme. The results showed that I-HWC lenses are more prone to Staphylococcus aureus adhesion than NI-LWC lenses, both untreated (+15.4%) and treated with lysozyme (+20.5%). Lysozyme increased bacterial adhesion by 30.5% on the lenses with lower water content, and by 36.3% on those with higher water content.
 ...
PMID:Disposable contact lenses and bacterial adhesion. In vitro comparison between ionic/high-water-content and non-ionic/low-water-content lenses. 757 71

Adherence of 18 staphylococcal strains to 13 types of uncoated plastic tubes made from 10 different plastic materials were investigated by binding of radiolabelled bacteria in phosphate-buffered saline for 2 h at 37 degrees C. The different materials could be divided into five groups based on their ability to bind staphylococci. Lowest adhesion was found for plasticised polyvinylchloride. Simple assays for the relative binding of peroxidase-labelled human IgG or fibrinogen did not predict the result of adhesion studies. Neither bacterial surface hydrophobicity measured in a two-phase partitioning assay, nor hydrophobicity of materials (wettability) as measured by their contact angles in water correlated with bacterial adhesion. Adhesion of staphylococci to certain plastic materials was greatly influenced by the method used for sterilisation of the material.
 ...
PMID:Attachment of staphylococci to different plastic tubes in vitro. 828 13

Adhesion characteristics of fibroblastic baby hamster kidney (BHK) cells and epithelial Madine Darby kidney (MDBK) cells on polyurethane (PU) and polyhydroxyethylmethacrylate (PHEMA) based surfaces have been studied. PU surfaces were prepared by a classical solvent-casting procedure of Pellethane solution that contains different types of solvents, i.e., THF, dioxane and their compositions. PHEMA based surfaces were obtained by bulk polymerization of respective comonomers (HEMA, acrylic acid, AA, and dimethylaminoethylmethacrylate, DMAEMA) in the presence of the crosslinker. Thus, a number of polymeric surfaces were obtained with different surface charges (COO- and NH+4) and with different surface free energies in a range between 60-82 ergs/cm2. Surface properties of these membranes were characterized by equilibrium water contents, air and octane contact angles, surface free energies, SEM photographs and ATR-FTIR spectra. Interactions of BHK and MDBK cells with the surfaces were examined in stationary culture conditions which were carried out in MEM supplemented with fetal calf serum. The observations strongly suggested that the chemical and/or physical properties of membrane surface and morphology of the cell control the degree of cell adhesion to the PU and PHEMA based membranes.
 ...
PMID:Relationship of surface characteristics to cellular attachment in PU and PHEMA. 845 35

We have developed a chemical treatment for the mica surface which allows biopolymers to be held in place for atomic force microscopy, even under water, using conventional, untreated force sensing tips. We illustrate the procedure with images of lambda DNA and fd phage. The phage adheres well enough to permit in situ imaging of the adsorption process in water. These experiments yield a mean length for the phage of 883 +/- 72 nm. This compares with a measured length of 883 +/- 33 nm when the phage are imaged after drying following adsorption from water, showing that the effect of dehydration is quite small. Adhesion forces between the force sensing tip and the substrate and the sensing tip and the biomolecules are very different in the three media (air, water and propanol). The apparent height of the phage and the width and height of the DNA depends upon these adhesion forces quite strongly. In contrast, changing the Hookean spring force exerted by the scanning tip makes little difference. These results suggest that the chemical factors involved in adhesion can dominate atomic force images and that the composition of the scanning tip is at least as important a factor as its geometry.
 ...
PMID:Atomic force microscopy of DNA and bacteriophage in air, water and propanol: the role of adhesion forces. 846 97

Aeromonas strains (total = 60) of clinical, water and food origin were tested for adherence to HEp-2 cells. Environmental strains were selected (except for A. caviae) to include primarily those expressing other virulence-associated properties. Adhesion was markedly species-dependent (A. veronii biotype sobria, 15 of 26 [58%]. A caviae, 4 of 12 [33%] and A. hydrophila, 2 of 8 [11%]). A. veronii biotype sobria were adhesive, irrespective of source (62 and 54% for clinical and environmental strains, respectively). Adherent strains of this species were enterotoxin-positive and most (13 of 15) grew at 43 degrees C. A. caviae isolated from clinical specimens contained a higher proportion (75%) of adherent strains than environmental strains (13%). Virulent subsets of A. veronii biotype sobria and A. caviae are adherent to HEp-2 cells. The HEp-2 assay is a useful model for investigating mechanisms of adherence and enteropathogenicity of virulent Aeromonas species.
 ...
PMID:Adherence to HEp-2 cells and enteropathogenic potential of Aeromonas spp. 847 72


<< Previous 1 2 3 4 5 6 7 8 9 10 Next >>