Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: KEGG:D01931 (TiO2)
 11,320 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

A new method using nanoparticle TiO2 as solid-phase extractant coupled with ICP-AES was proposed for simultaneous determination of trace elements. The adsorption behavior of nanometer TiO2 towards Cu, Cr, Mn and Ni was investigated by ICP-AES, and the adsorption pH curves, adsorption isotherms and adsorption capacities were obtained. It was found that the adsorption rates of the metal ions studied were more than 90% in pH 8.0-9.0, and 2.0 mol L-1 HCl was sufficient for complete elution. Nanometer TiO2 possesses a significant capacity for the sorption of the metal ions studied which is higher than the capacity of silica, the commonly used extractant. The method has been applied to the analysis of some environmental samples with satisfactory results.
 ...
PMID:Study of the adsorption behavior of heavy metal ions on nanometer-size titanium dioxide with ICP-AES. 1122 17

Calibration materials for microanalysis of Ti minerals have been prepared by direct fusion of synthetic and natural materials by resistance heating in high-purity graphite electrodes. Synthetic materials were FeTiO3 and TiO2 reagents doped with minor and trace elements; CRMs for ilmenite, rutile, and a Ti-rich magnetite were used as natural materials. Problems occurred during fusion of Fe2O3-rich materials, because at atmospheric pressure Fe2O3 decomposes into Fe3O4 and O2 at 1462 degrees C. An alternative fusion technique under pressure was tested, but the resulting materials were characterized by extensive segregation and development of separate phases. Fe2O3-rich materials were therefore fused below this temperature, resulting in a form of sintering, without conversion of the materials into amorphous glasses. The fused materials were studied by optical microscopy and EPMA, and tested as calibration materials by inductively coupled plasma mass spectrometry, equipped with laser ablation for sample introduction (LA-ICP-MS). It was demonstrated that calibration curves based on materials of rutile composition, within normal analytical uncertainty, generally coincide with calibration curves based on materials of ilmenite composition. It is, therefore, concluded that LA-ICP-MS analysis of Ti minerals can with advantage be based exclusively on calibration materials prepared for rutile, thereby avoiding the special fusion problems related to oxide mixtures of ilmenite composition. It is documented that sintered materials were in good overall agreement with homogeneous glass materials, an observation that indicates that in other situations also sintered mineral concentrates might be a useful alternative for instrument calibration, e.g. as alternative to pressed powders.
 ...
PMID:Preparation of calibration materials for microanalysis of Ti minerals by direct fusion of synthetic and natural materials: experience with LA-ICP-MS analysis of some important minor and trace elements in ilmenite and rutile. 1156 58

A new method for the determination of free La3+ and La organic complexes in solution using a nanometer-sized titanium dioxide as solid-phase extractant and fluorination-assisted electrothermal vaporization (FETV)-ICP-AES as sensitive detector has been developed. The effect of pH on the adsorption characteristics of La3+ and La complexes of citric acid, 2-hydroxyisobutyric acid (HIBA), and humic acid on nanometer-sized TiO2 was investigated and optimized. On the basis of the difference in volatility between fluoride of analyte (lanthanum) and the fluoride of matrix (titanium), an in-situ removal of the adsorbent matrix (TiO2) from a graphite furnace was realized. Therefore, the free La3+ and adsorbed La complexes on nanometer-sized titanium dioxide could be determined respectively by FETV-ICP-AES without any other chemical pretreatment. The proposed method was applied for the determination of free ion (La3+) and La complexes in synthetic solutions and soil extracts with satisfactory results.
 ...
PMID:Selective separation of La3+ and lanthanum organic complexes with nanometer-sized titanium dioxide and their detection by using fluorination-assisted electrothermal vaporization ICP-AES with in-situ matrix removal. 1511 31

In this study, the general toxicity tests including acute toxicity test, haemolysis test, MTT assay of Ti-Fe-Mo-Mn-Nb-Zr alloys were carried out. The morphology of these cells was also observed under phase-contrast microscope. By using X-ray photoelectron spectroscopy(XPS), the kind and mol% of element in surface film were studied. The kind and concentration of element in dipping fluid were investigated by ICP atomic emission spectrometry. The results showed the primary component is TiO2 in surface film. The dipping fluid of Ti-Fe-Mo-Mn-Nb-Zr alloys contains Fe 0.2-1.07 mg/l and Mn 0.16-0.5 mg/l; such dental materials are beneficial to health. No cytotoxic effect was disclosed by in vitro and in vivo tests. The level of cytotoxicity was grade 0 and 1; the haemolysis degree was 0.558%-0.642%, i.e. less than 5%. The cells growing in the extract showed normal morphology. These data indicate that Ti-Fe-Mo-Mn-Nb-Zr alloy, as a dental material, has good biocompatibility.
 ...
PMID:[Evaluation on biocompatibility of Ti-Fe-Mo-Mn-Nb-Zr alloy]. 1514 39

Effects of Ce on the short-term biocompatibility of Ti-Fe-Mo-Mn-Nb-Zr alloy designed for implant materials were studied by acute toxicity test, hemolytic test, and MTT assay. The elements and their concentration in surface films and extraction media of Ti alloys were investigated with XPS and ICP, respectively. The primary compositions of the surface films of Ti alloys with 0.3% Ce and without Ce were TiO2 and Nb2O5. There were 0.2 mg/l Fe and 0.16 mg/l Mn in the extraction medium of Ti alloy without Ce, while 0.27 mg/l Fe and 0.87 mg/l Mn in the extraction medium of Ti alloy with 0.3% Ce. The concentrations of Fe and Mn in the medium were too low to have any significant effects on human health. There was no sign of cytotoxicity in these tests. The cytotoxicity levels of Ti alloys without Ce and with 0.3% Ce were graded 0 and 1, respectively. The hemolytic degrees of Ti alloys without Ce and with 0.3% Ce were 0.558% and 0.67%, respectively. The cells being incubated in the extraction medium were normal. These phenomena indicated that Ce was innocuous within the concentration range of this study. In addition, the hemolytic ratio and toxicity level of Ti alloy with 0.3% Ce were a little higher than that of Ti alloy without Ce. This meant that Ce would slightly increase the toxicity of Ti alloy.
 ...
PMID:Effects of Ce on the short-term biocompatibility of Ti-Fe-Mo-Mn-Nb-Zr alloy for dental materials. 1534 36

The adsorption behavior of Cd, Co and Zn on nanometer-size TiQ2 was investigated. At pH 9.0, Cd, Co and Zn were retained on the nanometer-size TiO2, then eluted with 0.1 mol x L(-1) HNO3 and determined by ICP-AES. The adsorption capacities of nanometer TiO2 were found to be 8.1, 6.9 and 15.1 mg x g(-1) for Cd, Co and Zn respectively. The detection limits (3sigma) for Cd, Co and Zn are 5.1, 3.4 and 2.9 ng x mL(-1) respectively. The proposed method has been applied to the determination of trace Cd, Co and Zn in environmental samples with satisfactory results.
 ...
PMID:[Nanometer-size titanium dioxide separation/preconcentration and ICP-AES for the determination of Cd, Co and Zn]. 1601 28

By using dispersant polyacrylate amine (NH4PAA) to disperse TiO2, effects of different dispersants, pH value and the amount of dispersant on TiO2 slurry were investigated. The pH value of the medium and the dispersant amount were optimized, and a stable and homogeneous suspension was prepared. Nb in TiO2 was determined by an axial viewing ICP-OES spectrometer. At the same time, the performance of the axial viewing ICP-OES using solid powder analysis was discussed. Under the optimum experimental conditions, the detection limit of the present method is 3.0 microg x L(-1) and the RSD is 3.1% (n = 3, c = 0.3 mg x L(-1)).
 ...
PMID:[Direct determination of Nb in titanium oxide using slurry sample introduction by axial viewing inductively coupled plasma optical emission spectrometry]. 1609 84

The mole fractions of hydroxo complexes of titanium(IV) ion in an aqueous solution with 0.10 mol dm(-3) NaClO4 at 25 degrees C have been determined as a function of pH by a newly developed analytical procedure based on UV spectrophotometry, using a metastable homogeneous solution of 1.25 x 10(-4) mol dm(-30 in total concentration of Ti(IV). Also, the total concentration of the hydroxo complexes in equilibrium with Ti(OH)4 solid, or the solubility of Ti(OH)4 solid in an inhomogeneous system, has been obtained by ICP measurement for the solution phase. A combination of these data yielded the absolute concentration of each complex species in equilibrium with Ti(OH)4 solid. Finally, Ti(OH)+3 complex has been assigned to the precursor for the formation of anatase TiO2 nanoparticles transformed from Ti(OH)4 gel from a comparison between the above equilibrium data and a kinetic study on the formation rate of the anatase TiO2 particles in the gel-sol system.
 ...
PMID:Synthesis of uniform anatase TiO2 nanoparticles by gel-sol method. 1. Solution chemistry of Ti(OH)(4-n)+(n) complexes. 1629 Jul 98

Alloys based on titanium or cobalt have been used as implant materials for decades with good success. Because of their natural oxide layer these alloys reveal good corrosion behaviour. In contact with physiological solution metal release takes place, which can cause inflammation. Coatings can improve the corrosion behaviour. In this study Ti6Al4V and Co28Cr6Mo alloys, which are frequently used as implant materials, were tested. Polished discs of these alloys and polished discs, which were coated with TiO2-layers by sol-gel chemistry, were compared regarding their corrosion behaviour and metal ion releasing. The releasing of Al, V, Ti, Co, Cr and Mo was quantified by ICP-MS analysis. The TiO2-coating reduced the release of all ions except of the Al-ion. Both alloys showed a deviating kinetic of ion releasing. In addition, cell response (cell vitality, cell proliferation, endothelial marker CD31 and actin allocation) of osteoblasts and endothelial cells were investigated.
 ...
PMID:[Corrosion behaviour, metal release and biocompatibility of implant materials coated by TiO2-sol gel chemistry]. 1630 47

The monitoring of craniospinal compliance is uncommonly used clinically despite it's value. The Spiegelberg compliance monitor calculates intracranial compliance (C = deltaV/deltaP) from a moving average of small ICP perturbations (deltaP) resulting from a sequence of up to 200 pulses of added volume (deltaV = 0.1 ml, total V = 0.2 ml) made into a double lumen intraventricular balloon catheter. The objective of this study was thus to determine the effectiveness of the decompressive craniectomy done on the worst brain site with regard to compliance (Cl), pressure volume index (PVI), jugular oximetry (SjVo2), autoregulation abnormalties, brain tissue oxygen (TiO2) and cerebral blood flow (CBF). This is a prospective cohort study of 17 patients who were enrolled after consent and approval of the ethics committee between the beginning of the year 2001 and end of the year 2002. For pre and post assessment on compliance and PVI, all 12 patients who survived were reported to become normal after decompressive craniectomy. There is no significant association between pre and post craniectomy assessment in jugular oxymetry (p > 0.05), autoregulation (p > 0.05), intracranial brain oxymetry (p = 0.125) and cerebral blood flow (p = 0.375). Compliance and PVI improved dramatically in all alive patients who received decompressive craniectomy. Compliance and PVI monitoring may be crucial in improving the outcome of severe head injured patients after decompressive craniectomy.
 ...
PMID:Preliminary report on spiegelberg pre and post-operative monitoring of severe head-injured patients who received decompressive craniectomy. 1646 72


1 2 3 4 5 6 7 Next >>