Gene/Protein Disease Symptom Drug Enzyme Compound
Pivot Concepts:   Target Concepts:
Query: KEGG:D01931 (TiO2)
 11,320 document(s) hit in 31,850,051 MEDLINE articles (0.00 seconds)

The effect of surface roughness on osteoblast proliferation, differentiation, and protein synthesis was examined. Human osteoblast-like cells (MG63) were cultured on titanium (Ti) disks that had been prepared by one of five different treatment regimens. All disks were pretreated with hydrofluroic acid-nitric acid and washed (PT). PT disks were also: washed, and then electropolished (EP); fine sandblasted, etched with HCl and H2SO4, and washed (FA); coarse sandblasted, etched with HCl and H2SO4, and washed (CA); or Ti plasma-sprayed (TPS). Standard tissue culture plastic was used as a control. Surface topography and profile were evaluated by brightfield and darkfield microscopy, cold field emission scanning electron microscopy, and laser confocal microscopy, while chemical composition was mapped using energy dispersion X-ray analysis and elemental distribution determined using Auger electron spectroscopy. The effect of surface roughness on the cells was evaluated by measuring cell number, [3H]thymidine incorporation into DNA, alkaline phosphatase specific activity, [3H]uridine incorporation into RNA, [3H]proline incorporation into collagenase digestible protein (CDP) and noncollagenase-digestible protein (NCP), and [35S]sulfate incorporation into proteoglycan. Based on surface analysis, the five different Ti surfaces were ranked in order of smoothest to roughest: EP, PT, FA, CA, and TPS. A TiO2 layer was found on all surfaces that ranged in thickness from 100 A in the smoothest group to 300 A in the roughest. When compared to confluent cultures of cells on plastic, the number of cells was reduced on the TPS surfaces and increased on the EP surfaces, while the number of cells on the other surfaces was equivalent to plastic. [3H]Thymidine incorporation was inversely related to surface roughness. Alkaline phosphatase specific activity in isolated cells was found to decrease with increasing surface roughness, except for those cells cultured on CA. In contrast, enzyme activity in the cell layer was only decreased in cultures grown on FA- and TPS-treated surfaces. A direct correlation between surface roughness and RNA and CDP production was found. Surface roughness had no apparent effect on NCP production. Proteoglycan synthesis by the cells was inhibited on all the surfaces studied, with the largest inhibition observed in the CA and EP groups. These results demonstrate that surface roughness alters osteoblast proliferation, differentiation, and matrix production in vitro. The results also suggest that implant surface roughness may play a role in determining phenotypic expression of cells in vivo.
 ...
PMID:Effect of titanium surface roughness on proliferation, differentiation, and protein synthesis of human osteoblast-like cells (MG63). 754 45

The goal of this study was to investigate the effect of bone cell response to titanium (Ti) surfaces in the presence of bone morphogenetic protein (BMP)-atelopeptide type I collagen mixture. The atelopeptide type I collagen was used as a potential carrier for the BMP. Sterilized 600-grit Ti samples were used as substrates for the cell culture study. X-ray photoelectron spectroscopy indicated the presence of TiO2 on the Ti surface. The in vitro cell culture study was performed using an osteoblast progenitor cell line derived from mice (2T9). At confluency, the cells cultured on Ti surfaces were divided into three groups: unstimulated culture, culture stimulated by BMP-atelopeptide type I collagen (40 ng/mL), and culture stimulated by atelopeptide type I collagen (40 ng/mL). The unstimulated and atelopeptide type I collagen cultures were controls in this study. After 4 days of incubation, protein production, alkaline phosphatase (ALP) activity, and hexosaminidase activity were observed to be the highest for cells exposed to the BMP-atelopeptide type I collagen mixture. Statistical differences in cellular protein production and ALP activity were observed between the controls and the surfaces exposed to the BMP-atelopeptide type I collagen mixture. Similarly, a statistical difference in hexosaminidase activity was observed between unstimulated Ti surfaces and surfaces exposed to BMP-atelopeptide type I collagen mixture. However, no statistical differences in protein production, ALP activity, and hexosaminidase activity were observed between cells exposed to atelopeptide type I collagen solution and the unstimulated surfaces.
 ...
PMID:Osteoblast progenitor cell responses to characterized titanium surfaces in the presence of bone morphogenetic protein-atelopeptide type I collagen in vitro. 1055 Nov 43

The clinical success of dental implants is governed in part by surface properties of implants and their interactions with the surrounding tissues. The objective of this study was to investigate the effect of heat-treated titanium (Ti) surfaces on protein adsorption and osteoblast responses in vitro. The passivated Ti samples used in this study were either nonheat-treated or heat-treated at 750 degrees C for 90 minutes. Using x-ray diffraction analyses, no oxide peaks were observed on the nonheat-treated surfaces, suggesting an amorphous oxide. Crystalline rutile TiO2 peaks were observed on the heat-treated Ti surfaces. The contact angles of water on heat-treated Ti surfaces (32.0 +/- 2.5 degrees) were statistically lower compared with the nonheat-treated Ti surfaces (47.7 +/- 2.3 degrees). In addition, the mean albumin concentration on the nonheat-treated Ti surfaces (3.57 +/- 0.33 micrograms/mL) was observed to be significantly different from the mean albumin concentration on heat-treated Ti surfaces (2.25 +/- 0.26 micrograms/mL). In the presence of an osteoblast precursor cell line, significantly different hexosaminidase activity, protein production, and alkaline phosphatase activity were observed for cells grown on heat-treated Ti surfaces compared with nonheat-treated Ti surfaces.
 ...
PMID:Protein adsorption and osteoblast responses to heat-treated titanium surfaces. 1063 54

The biocompatibility of titania/hydroxyapatite (TiO2 /HA) composite coatings, at different ratio obtained by sol-gel process, were investigated studying the behaviour of human MG63 osteoblast-like cells. The biocompatibility was evaluated by means of cytotoxicity and cytocompatibility tests. Cytotoxicity tests, i.e., neutral red (NR), MTT and kenacid blue (KB) assays, were performed to assess the influence of the material extracts on lysosomes, mitochondria and cell proliferation, respectively. Cell proliferation, some preliminary indications of cell morphology, alkaline phosphatase activity, collagen and osteocalcin production of MG63 cells, cultured directly onto TiO2/HA substrates, were evaluated. The results showed that these materials have no toxic effects. Cell growth and morphology were similar on all the materials tested: on the contrary, alkaline-phosphatase-specific activity and collagen production of osteoblasts cultured on TiO2/HA coatings were significantly higher than uncoated titanium and polystyrene of culture plate and were influenced by chemical composition of the coatings. In particular, TiO2/HA coating at 1:1 ratio (w/w) seems to stimulate more than others the expression of some differentiation markers of osteoblastic phenotype. TiO2/HA coatings resulted to be bioactive owing to the presence of hydroxyl groups detected on their surface that promote the calcium and phosphate precipitation and improve the interactions with osteoblastic cells.
 ...
PMID:The influence of titania/hydroxyapatite composite coatings on in vitro osteoblasts behaviour. 1137 45

Hydroxyapatite (HA) was coated onto a titanium (Ti) substrate with the insertion of a titania (TiO2) buffer layer by the sol-gel method. The HA layer was employed to enhance the bioactivity and osteoconductivity of the Ti substrate, and the TiO2 buffer layer was inserted to improve the bonding strength between the HA layer and Ti substrate, as well as to prevent the corrosion of the Ti substrate. The HA layer coated over the TiO2 showed a typical apatite phase at 400 degrees C and the phase intensity increased above 450 degrees C. The sol-gel derived HA and TiO2 films, with thicknesses of approximately 800 and 200 nm, respectively, adhered tightly to each other and to the Ti substrate. The bonding strength of the HA/TiO2 double layer coating on Ti was markedly improved when compared to that of the HA single coating on Ti. The highest strength of the double layer coating was 55 MPa after heat treatment at 500 degrees C. The improvement in bonding strength with the insertion of TiO2 was attributed to the resulting enhanced chemical affinity of TiO2 toward the HA layer, as well as toward the Ti substrate. Human osteoblast-like cells, cultured on the HA/TiO2 coating surface, proliferated in a similar manner to those on the TiO2 single coating and on the pure Ti surfaces. However, the alkaline phosphatase activity of the cells on the HA/TiO2 double layer was expressed to a higher degree than that on the TiO2 single coating and pure Ti surfaces. The corrosion resistance of Ti was improved by the presence of the TiO2 coating, as confirmed by a potentiodynamic polarization test.
 ...
PMID:Hydroxyapatite coating on titanium substrate with titania buffer layer processed by sol-gel method. 1475 38

Hydroxyapatite (HA) composites with titania (TiO2) up to 30 mol % were coated on a titanium (Ti) substrate by a sol-gel route, and the mechanical and biological properties of the coating systems were evaluated. Using polymeric precursors, highly stable HA and TiO2 sols were prepared prior to making composite sols and coatings. Coatings were produced under a controlled spinning and heat treatment process. Pure phases of HA and TiO2 were well developed on the composites after heat treatment above 450 degrees C. The HA-TiO2 composite coating layers were homogeneous and highly dense with a thickness of about 800-900 nm. The adhesion strength of the coating layers with respect to Ti substrate increased with increasing the TiO2 addition. The highest strength obtained was as high as 56 MPa, with an improvement of about 50% when compared to pure HA (37 MPa). The osteoblast-like cells grew and spread actively on all the composite coatings. The proliferation and alkaline phosphatase (ALP) activity of the cells grown on the composite coatings were much higher than those on bare Ti, and even comparable to those on pure HA coating. Notably, the HA-20% TiO2 composite coating showed a significantly higher proliferation and ALP expression compared to bare Ti (p < 0.05). These findings suggest that the sol-gel-derived HA-TiO2 composite coatings possess excellent properties for hard tissue applications from the mechanical and biological perspective.
 ...
PMID:Hydroxyapatite and titania sol-gel composite coatings on titanium for hard tissue implants; mechanical and in vitro biological performance. 1548 Oct 86

In this study, we introduce a porous composite material, termed "Ecopore", and describe in vitro investigation of the material and its modification with fibronectin. The material is a sintered compound of rutile TiO2 and the volcanic silicate perlite with a macrostructure of interconnecting pores. It is both inexpensive and easy to manufacture. We first investigated Ecopore for corrosion and leaching of elements in physiological saline. The corrosion supernatants did not contain critical concentrations of toxic trace elements. In an in vitro model, human primary osteoblasts (HOB) were cultured directly on Ecopore. HOB grew on the composite as well as on samples of its single constituents, TiO2 and perlite glass, and remained vital, but cellular spreading was less than on tissue culture plastic. The pro-inflammatory cytokines IL-1 and TNF-alpha were below detection limits in HOB culture supernatants, whereas IL-6 was detectable on a low level. To enhance cellular attachment and growth, the surface of the composite was modified by etching, functionalization with aminosilane and coupling of fibronectin. This modification greatly enhanced the spreading of HOB, indicated by vital staining and Sodium 3'-[1-(phenylaminocarbonyl)-3,4-tetrazolium]-bis (4-methoxy-6-nitro) benzene sulfonic acid hydrate (XTT) metabolism assays. HOB grew on the entire visible surface of porous fibronectin-modified composite, expressing alkaline phosphatase, a mature osteoblast marker. We conclude that Ecopore is non-toxic and sustains HOB growth, cellular spreading being improvable by coating with fibronectin. The composite may be usable in the field of bone substitution.
 ...
PMID:In vitro behavior of a porous TiO2/perlite composite and its surface modification with fibronectin. 1560 77

Titanium (Ti) is used for implantable devices because of its biocompatible oxide surface layer. TiO2 surfaces that have a complex microtopography increase bone-to-implant contact and removal torque forces in vivo and induce osteoblast differentiation in vitro. Studies examining osteoblast response to controlled surface chemistries indicate that hydrophilic surfaces are osteogenic, but TiO2 surfaces produced until now exhibit low surface energy because of adsorbed hydrocarbons and carbonates from the ambient atmosphere or roughness induced hydrophobicity. Novel hydroxylated/hydrated Ti surfaces were used to retain high surface energy of TiO2. Osteoblasts grown on this modified surface exhibited a more differentiated phenotype characterized by increased alkaline phosphatase activity and osteocalcin and generated an osteogenic microenvironment through higher production of PGE2 and TGF-beta1. Moreover, 1alpha,25OH2D3 increased these effects in a manner that was synergistic with high surface energy. This suggests that increased bone formation observed on modified Ti surfaces in vivo is due in part to stimulatory effects of high surface energy on osteoblasts.
 ...
PMID:High surface energy enhances cell response to titanium substrate microstructure. 1592

Two glass ceramics in the CaO--P2O5--MgO system with the incorporation of K2O or TiO2 oxides were prepared with the goal of using them as potential bone graft substitutes. The incorporation of TiO2 and K2O led to the preparation of specific crystalline phases in the structure of the glass ceramics, which show different degrees of biodegradation. In fact, the 45CaO--45P2O5--5MgO--5K2O has been previously demonstrated to be much more soluble in aqueous solutions than the 45CaO--37P2O5--5MgO--13TiO2 glass ceramic. The in vitro biological activity of the two calcium phosphate glass ceramics was studied with the use of human bone marrow osteoblast cell cultures maintained for 28 days, and seeded materials were assessed for cell proliferation and function. The Ti-containing glass ceramic showed a stable surface throughout the culture time, on macroscopic and SEM observation. Osteoblast cells proliferated gradually, especially during the third week, with a high alkaline phosphatase activity and formation of a mineralized matrix. On SEM observation, attached cells appeared with a spread-polygonal morphology typical of the osteoblast cells, with extensive cell-to-cell contact. Cell behavior on the seeded material was similar to that found on cultures performed on tissue-culture-grade polystyrene; except for the presence of lower cell numbers during the first 2 weeks. By contrast, the K-containing glass ceramic showed a highly instable surface with dissolution/precipitation processes occurring throughout the culture time. Few cells adhered to the material surface, and subsequent proliferation was also hindered, especially from the first week onwards. Cell numbers were significantly lower than those observed in the Ti-containing glass ceramic during most of the incubation time. Results suggest that the different in vitro biological behavior of these two glass ceramics is mainly due to the significant differences in the surface degradation rate, which is directly correlated to the chemical composition of the mother glass.
 ...
PMID:In vitro studies of calcium phosphate glass ceramics with different solubility with the use of human bone marrow cells. 1598 37

Two surface-reactive sol-gel coatings, namely titania (TiO2) and a mixture of titania and silica (TiSi), were applied to titanium fiber meshes. Differentiation of rat bone marrow stromal cells toward an osteogenic phenotype with coated and uncoated (cpTi) substrates was compared. The amount of DNA in cpTi and TiSi matrices did not increase after day 3, but with TiO2 matrices the amount increased for 7 days. The prolonged period of proliferation with TiO2 scaffolds resulted in a delay in alkaline phosphatase induction. However, osteocalcin incorporation into extracellular matrix by day 14 was greater with TiO2 scaffolds than with cpTi scaffolds. Calcium deposition was also greater with TiO2-coated substrates than with uncoated substrates. With the TiSi scaffolds osteocalcin production and mineralization were lower than with the cpTi scaffolds. The current study confirms our previous findings that titanium fiber mesh supports attachment, growth, and differentiation of rat bone marrow stromal cells. Furthermore, the osteogenic capacities of cell-scaffold constructs under cell culture conditions were increased with a sol-gel-derived titania coating, but not with a titania-silica coating.
 ...
PMID:Osteoblast differentiation with titania and titania-silica-coated titanium fiber meshes. 1625 3


1 2 3 4 5 6 7 Next >>